User manual EMPHASER EX15T4

[. . . ] BLACK NOMEXTM DOUBLE SPIDER All three T4 woofer models deploy mirrored NomexTM double spiders with huge diameters and progressive deflection characteristics. The double spider suspensions always keep the voice coils in tight and perfect alignment. NomexTM material stands out with its unparalleled durability against mechanical failure, aging or any other degradation based on physical strain. 4-LAYER WOUND CCAW VOICE COIL 4-layer wound copper clad alumimum voice coils with extended winding heights provide the necessary thermal power handling for high SPL output, but keep the moving mass low for increased efficiency. [. . . ] The straight cone geometry and the Nomex composite material give you stronger bass output and lower distortion, as less cone flex means a more piston like movement of the cone in the entire bass range. To improve reliability in the field, the surround is stitched to the cone, removing unnecessary strain from the adhesive that is holding the surround to the cone. TECHNICAL SPECIFICATIONS: Usable Frequency Response* Continuous Power Handling* Peak Power Handling* Nominal Impedance Voice Coil Diameter Voice Coil Winding Height Front Pole Plate Height Total Weight of Sr-Fe Magnet *Exact performance data depending upon actual enclosure! EX10T4 25 - 100 Hz 700 W RMS* 1400 W* 4 Ohms 2 ½" / 65. 5 mm 38 mm 10 mm 100 oz. / 2835 g EX12T4 20 ­ 100 Hz 1000 W RMS* 2300 W* 4 Ohms 3" / 76. 2 mm 38 mm 10 mm 122 oz. / 3460 g EX15T4 20 ­ 100 Hz 1000 W RMS* 2800 W* 4 Ohms 3" / 76. 2 mm 38 mm 10 mm 122 oz. / 3460 g THIELE - SMALL PARAMETERS Free-Air Resonance DC Resistance Electrical Damping Mechanical Damping Total Damping Equivalent Volume of Compliance Moving Mass incl. Air Load Electrically Limited Cone Excursion Effective Cone Surface Volume Displacement of Cone Voice Coil Inductance @ 1kHz Efficiency (2. 00V) (Fs) (Re) (Qes) (Qms) (Qts) (Vas) (Mms) (Xmax) (Sd) (Vd) (Le) (RefSPL) 33 Hz 3. 73 Ohms 0. 48 7. 6 0. 45 27. 1 l 176 g 14. 0 mm 380 cm² 1064 cm³ 2. 94 mH 84. 8 dB/1W/1m 26 Hz 3. 63 Ohms 0. 41 7. 5 0. 39 66. 3 l 223 g 14. 0 mm 539 cm² 1509 cm³ 2. 77 mH 86. 6 dB/1W/1m 26 Hz 3. 22 Ohms 0. 61 9. 2 0. 57 114. 7 l 350 g 14. 0 mm 866 cm² 2425 cm³ 2. 63 mH 86. 9dB/1W/1m X-TREME T4 WOOFER SPECIFICATION SHEET MOUNTING DIMENSIONS Mounting Cutout Diameter Rear Mounting Clearance (Mounting Depth) EX10T4 235 mm 169 mm EX12T4 282 mm 188 mm EX15T4 322 mm 221 mm ENCLOSURE SUGGESTIONS EMPHASER Laboratories recommend to use the T4 woofers in combination with sealed, vented and bandpass enclosures. To obtain the best possible performance of this woofer in your car audio system, make sure to follow the stated basic enclosure suggestions listed below. If the provided enclosure suggestions listed below are not applicable to your system, contact your authorized EMPHASER dealer to ask for further assistance. SEALED ENCLOSURE Net Volume: PORTED ENCLOSURE I (SPL) Net Volume: Inner Diameter of Port: Length of Port: PORTED ENCLOSURE II (LOW BASS) Net Volume: Inner Diameter of Port: Length of Port: BANDPASS ENCLOSURE Net Volume Ported Chamber: Net Volume Sealed Chamber: Inside Diameter of Ports: Port Length: 25 l 35 l 1 x 10 cm 18 cm 35 l 1 x 10 cm 25 cm 20 l 15 l 1 x 10 cm 15 to 23 cm 35 l 55 l 2 x 10 cm 24 cm each 55 l 1 x 10 cm 28 cm 28 l 24 l 2 x 10 cm 22 to 27 cm each 65 l 95 l 2 x 10 cm 20 cm each 95 l 2 x 10 cm 27 cm each 55 l 45 l 3 x 10 cm 18 to 23 cm each OVERKILL OVERKILL OVERKILL LEGEND: MINIMUM 3 OPTIMUM 3 SHORT TERM 3 O VERKILL POWER GRAPH T4 WOOFERS The power graph illustration allows to pick an amplifier to achieve a good power match between the T4 driver and the amp. The OPTIMUM zone is the , , safe operating area" for each T4 subwoofer. Folllowing these suggestion will allow you subwoofer to take advantage of full T4 driver performance without chances of failure due to excessive heat and/or mechanical stress. Be wise, make an appropriate choice! MINIMUM 3 Will not give you optimum performance this woofer model can offer, but the suspension and the coil always work at a comfortable level. Do not operate the amplifier fer fer, connected to the T4 woofer at full playback volume for prolonged periods of time, as clipping induced failures may result. O P T I M U M 3 Will give you a good compromise between sound quality, long-term reliability, high SPL output and low-distortion playback performance!quality reliability SHORT TERM 3 Power levels within this zone may give you a little more audible output, at the cost of overstressing the suspension system and exceeding thermal headroom of the voice-coil. Life span of product may be adversely affected. t only OVERKILL 3 Power fed to the woofer at or above this level will - sooner or later - render the suspension system or voice-coil defective. Failures of any kind, ocurring at this level, are not covered under warranty! ENCLOSURE CONSTRUCTION / CABINET DAMPING / BREAK-IN INFO Always use 22 mm MDF or birch plywood to build the enclosure. [. . . ] This warranty is limited to the original purchaser. purchaser Should your EMPHASER woofer require warranty service, please return it to the retailer from whom it was purchased. Please do not send any product to EMPHASER Inc. , Wyoming, Michigan U. S. A. Should you have difficulty in finding an authorized EMPHASER dealer or service center, details are available from the national distributor in the country of purchase. [. . . ]