User manual ENCORE ENDSL-A2PLUSWIGX2

[. . . ] ENDSL-A2+WIGX2 ADSL2+ Modem With Four Port Ethernet and 802. 11g Wireless Router User's Manual August 2007 FCC Warning ENDSL-A2+WIGX2 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If it is enable, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. DHCP Server IP for relay agent: The DHCP server IP Address runs on WAN side. 46 6. 2. 5 DNS Relay The DNS Configuration allows the user to set the configuration of DNS. DNS Rely Selection: If user wants to disable this feature, he just needs to set both Primary & Secondary DNS to 0. 0. 0. 0. Using DNS relay, users can setup DNS server IP to 192. 168. 1. 1 on their computer. If not, device will perform as NO DNS relay. If you don't want to use the DNS Relay option, set the DNS relay to "Use User Discovered DNS Server Only" and set both Primary and Secondary DNS Servers to "0. 0. 0. 0". 47 6. 3 Wireless 6. 3. 1 Access Point Settings Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Set this attribute to be larger than the maximum MSDU (MAC Service Data Unit) size TURNS OFF the RTS/CTS handshake. Set this attribute to ZERO TURNS ON the RTS/CTS 48 handshake. Fragment Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. DTIM: This value is between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). 6. 3. 2 Multiple SSIDs Settings SSID: The SSID is a unique name to identify the ADSL Router in the Wireless LAN. Wireless Clients associating to the ADSL Router must have the same SSID. Broadcast SSID: Select No to hide the SSID such that a station can not obtain the SSID through passive scanning. Select Yes to make the SSID visible so a station can obtain in the SSID through Passive scanning. Channel ID: The range of radio frequencies used by IEEE 802. 11b/g wireless devices us called a channel. [Authentication Type] WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select Disable to allow all wireless computers to communicate with the access points without any data encryption. Select 64-bit WEP or 128-bit WEP to use data encryption. Key#1~Key#4 The WEP keys are used to encrypt data. Both the ADSL Router and the wireless clients must use the same WEP key for data transmission. If you chose 64-bit WEP, then enter any 10 hexadecimal digits ("0-9", "A-F") preceded by 0x for each key (1-4). [. . . ] When the ADSL LED begins to blink, the defaults have been restored and the router restarts. 3 The default username is "admin". The default password is "trendchip". The Password and Username fields are case-sensitive. [. . . ]