User manual ENCORE ENL832-TX-RENT

[. . . ] This adapter supports 10BASE-T/100BASE-TX Fast Ethernet and complies with the electrical and protocol requirements of the PCI Local Bus Specification, revision 2. 2. 1. 1 Features The 10/100 Fast Ethernet PCI adapter is a cost effective, high-performance network interface card. It operates in 10BASE-T and 100BASE-TX modes and integrates easily with Fast Ethernet hub and switch. IEEE 802. 3 10BASE-T and 100BASE-TX standards 32-bit bus master for high throughput and low CPU utilization Full-duplex operation at both 10Mbps and 100Mbps Supports 10/100Mbps auto-sensing capability Single shield RJ-45 connector for using at either Speed (Category 3, 4 or 5 UTP cable for 10Mbps Operation, and Category 5 UTP cable for 100Mbps Operation) Plug and Play Installation. 3 Network drivers on the diskette for Windows 95, 98, ME, NT, 2000, XP, NetWare, Unix and Packet driver. FCC, CE certification 1. 2 System Requirements To use the adapter, you need the following components: A PCI master mode expansion slot that is compliant with PCI bus specifications, revisions 2. 2 A 3. 5-inch, 1. 44MB diskette driver The following cables: To operate at 10Mbps, a Category 3, 4, 5 UTP/STP Cable To operate at 100Mbps, a Category 5 UTP/STP cable 2. [. . . ] Novell NetWare(client /server) Windows NT 3. 5, NT4. 0/2000/XP Windows 95/98/ME Microsoft Client (NDIS 2. 0 DOS/OS2) Windows For Workgroup 3. 11 . . . . and so on 2. 6 Software Installation Please refer to "Quick Installation Guide" 8 2. 7 Test Program This test program verifies configuration of the adapter and assists the isolation of any faults in operation. Test procedure are optional, and will only be useful in the unusual event that there is a fault, such as an interrupt number conflict among your computer's add on cards, If your installation provides normal operation, you do not need these test procedures. At your DOS prompt, type the following command: a:\rset8139. exe <Enter> The opening screen is displayed as following: View Current Configuration Set Up New Configuration Run Diagnostics Exit RSET8139 Choose <Set Up New Configuration> item allows you to set up the Network Speed, 10 or 100M, and Transmission Mode, Full or Half Duplex, and so on. Choose <Run Diagnostics> item to run the adapter test program. Adapter test program includes: <Run EEPROM Test>, <Run Diagnostics on Board>, <Run Diagnostics on Network>, and <Run Power Management Test>. The <Power Management Test> is available for WOL adapter only. 9 After choosing the <Run Diagnostics on Board> item, the screen will display like, Node ID. . . . . . . . : 00 e0 7d c0 00 01 Network Speed. . : 100Mbps I/O Base . . . . . . : E000H Interrupt . . . . . : 11 Full-Duplex . . . : Disabled Pass Count Count A. Cable Connection <Cable Connection> test reminds you that the connection link might be fail, either the cable is not connected or the cable link fails. For the <Run Diagnostics on Network> test, it is necessary to connect your computer with its supporting hub or another computer. This test cannot be completed except two computers on the LAN for sending or receiving the test packets between computers. 10 Fail 11 For the <Run Diagnostics On Network> test Ethernet Address 00E07DC00002 Target Machine Ethernet Address 00E07DC00001 Master Machine Netwok Master Machine: Master machine sends magic packet or Wake up frame through the network. Target Machine: Target machine is notified whenever a qualified wakeup packet is received. 12 Quick Installation Guide Please take the following steps for driver installation. Insert the adapter into the available PCI slot. After Microsoft Windows reboot, the PCI Ethernet Controller will be found. The system will prompt for driver installation. Insert the "Driver and Utilities" diskette into diskette driver and press <Enter>. For Windows 95, Key in a:\ path to install driver for the adapter 8. For Windows 98, Key in a:\w98_2000 path to install driver for the adapter 9. For Windows ME, Key in a:\winme path to install driver for the adapter 10. The Windows system will install the driver automatically. Reboot the Windows system. 13 Windows NT 1. Insert the adapter into the available PCI slot. [. . . ] After Microsoft Windows reboot, the 10/100Mbps Fast Ethernet Adapter will be found and the system will assign the default network driver to the adapter. Select "Control Panel" from "Start" menu bar 6. Select "Network Connection" folder then click "Local Area Connection" and "Properties". Click "Configure" item and select "Driver" 8. [. . . ]