User manual ENCORE ENUWI-G2

[. . . ] 4 Wireless utility setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Link Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When connected to the USB port and the driver were installed, the LNK LED will start blinking, and it means that the device is starting to scan an 802. 11g wireless device near the 802. 11g Wireless USB 2. 0 Adapter. While the 802. 11g Wireless USB 2. 0 Adapter linked up to the Access Point or to other Wireless LAN station, the LINK LED will always light up. 3 SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the 802. 11g Wireless USB 2. 0 Adapter. There are 2 ways to install the adapters: 1. Utility and Driver Installation using Adapter Setup Wizard (for Windows XP/Vista only) Insert Encore 802. 11g Wireless LAN Adapter Driver & Utility CD-ROM into computer's CD-ROM Drive and it will automatically run the Adapter Setup Wizard. Follow the on-screen instruction to set up the adapter. If the Wizard does not start automatically, go to your Windows Start menu and choose Run, type "D:\setup\nmasetup. exe" in the dialog box (D:\ will depend on where your CDROM drive is located). Note: (D:\ will depends on where the CD-ROM drive is located and <Windows OS> will depend on the Windows Operating System you are using) 2. Advanced Utility and Driver Installation, without Adapter Setup Wizard (for Windows Vista/XP/2000/ME/98) Insert the 802. 11g Wireless LAN USB 2. 0 Adapter Driver & Utility CD-ROM into computer's CD-ROM Drive and it will automatically run Adapter Setup Wizard. In some specific setting on Windows system, you may need to proceed the software manually, go to your Windows Start menu and choose Run, type "D:\Utility\XP_2K_ME_98\Setup. exe" or "D:\Utility\Vista\Setup. exe" in the dialog box (D:\ will depend on where your CD-ROM drive is located). Note: (D:\ will depends on where the CD-ROM drive is located and <Windows OS> will depend on the Windows Operating System you are using). The Install Shield Wizard screen will appear. Click "Next" to continue. 4 2. Click "Finish" to finish the installation. 5 3. Plug-in your 802. 11g Wireless USB 2. 0 Adapter into your computer's USB port. When start the utility first time, you will see the Wireless Configuration Utility Country Selector, select the country domain where you are using this Wireless device, users are responsible for ensuring that the region domain configuration is in compliance with the regulatory standards of these countries. . Warning: Be noted that selecting the incorrect region may result in a violation of applicable law; you will need to select the correct domain. You will see the icon on the Windows task bar when you finish the utility installation and plugged the 802. 11g Wireless USB 2. 0 Adapter. When the icon in the toolbar represents in green color, it is properly connected to the network and shown the linking quality. 6 WIRELESS UTILITY SETTING Windows® XP users may use the built-in wireless utility as default. The following instructions are for Service Pack 2 users. If you are using Windows® 2000/98/ME, you must use the Wireless Utility. With the Wireless utility, users can configure all the functions provided by the Wireless LAN Adapter Utility. Double-click the utility icon system tray. that appears in the The Wireless LAN Adapter Utility includes six tabs: Link Info, Configuration, Advanced, Site Survey and About. Link Info The Link Info screen shows you the status of the Wireless Adapter, it shows that where the device is connected to, the connect Status, the connecting Speed, the network Type, the Encryption type, the SSID and the Signal Strength. 7 Configuration This is the page where you can change the basic settings of the 802. 11g Wireless USB 2. 0 Adapter with the minimum amount of effort to implement a secure wireless network environment. SSID: The SSID differentiates one Wireless LAN group name from another; so all access points and all devices attempting to connect to a specific Wireless LAN group name must use the same SSID. [. . . ] Select Auto, Disable for other authentication feature. If one of the two options is selected, it is required to select the Encryption mode from the next dropping list. 9 Shared Key/Open System Network Key: Choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space. Key Length, Key Format and WEP Key: If you select 64bit in Hex format, you must type 10 values in the following range (0~F, hexadecimal), or 64bit in ASCII format, you must type 5 values in the following range (0~9, A~Z and a~z Alphanumeric). If you select 128bit in Hex format, you must type 26 values (0~F, hexadecimal), or 128bit in ASCII format, you must type 13 values in the following range (0~9, A~Z and a~z Alphanumeric). [. . . ]