User manual ENCORE ENXTV-X2

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATION USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ENCORE ELECTRONICS INC. ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. All Rights Reserved. 2 ENXTV-X2 User's Guide Contents: Chapter 1: Introduction 4 1. 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The audio speaker cable should be connected to the ENXTV-X2Audio-Out port when watching TV while the computer is turned off. 1. 1 Package Contents Please confirm the following parts are included when open the package. If not, please contact your distributor or dealer. ENXTV-X2 External TV Tuner IR Remote Control 2 pc. AAA Batteries (for remote controller) Switching AC adapter VGA-In loop back cable (for PIP mode) 3. 5 mm stereo Audio cable User's Manual 1. 2 System Requirements Display unit CRT / LCD with Standard VGA connector (D-Sub 15 pin). A computer is necessary when in PIP mode. Independent of OS (operating system), no software driver installation or HDD space is needed. 1. 3 Main Features Resolution up to WSXGA: 1680x1050 Resolution. The most optimized VIDEO display setting is 1024×768 with the vertical refresh rate at 75Hz gives the best performance In a generic 15 inch LCD monitor, while in 20 inch LCD Wide monitor users can set up to 1680x1050 PIP Function supports sub-Video display in PC: In addition to a full screen display, the PIP feature allow the user to watch TV programs while using the computer, the PIP sub video Window can be move around to the any places of the monitor screen. 16 Channels TV wall for program preview: The TV program can be previewed with 4 , 9 or 16 display Windows, and can be easily manipulated by a function key or remote control key More sharper and stunning pictures: Adaptive 3D noise reduction filter. Enhanced motion adaptive 3D de-interlacing and adaptive Luma/Chroma enhanced engine. Multiple input/output source: Supported connectors include (RCA) input and outputS-VHS input3. 5 mm stereo audio input and outputconvert for VCRDVD connection. Chapter 2: Getting Started 2. 1 Rear panel connectors ENXTV-X2 cable connection is easy. The most typical cable connections are shown in the picture diagram below. Make sure the power cable is not connected when hooking these cables in. CONNECTOR DC In VGA Out TYPE 5mm, INT+, EXT15 pin D-Sub connector DESCRIPTION AC adapter, power in (5V, 2 A) ENXTV-X2 main video output. Connects to CRT/LCD Monitor VGA-In loop back cableThe other end of this cable connects to the PC's VGA D-sub 15 pin connector. Audio out connects to the speaker. VGA In 8pin Mini DIN connector Audio Out Audio In Video Out 3. 5mm stereo connector 3. 5mm stereo connector RCA Jack Audio In Connect to PC sound system (Audio-out of sound card). Can be used to connect to Video input of display unit RF TV antenna connector TV or CATV signal-in connector 2. 2 Right Side Panel Port Connectors CONNECTOR S-Video In TYPE 7-pin Min Din connector DESCRIPTION S-VHS type external video input source. Can be used for DVD, VCR or Camcorder External composite video input source, can be connected to DVD, VCR or Camcorder. Video In RCA Jack Audio In (L/R) RCA Audio jack RCA audio jack used for external audio input source. 2. 3 Cable Connections There is no sequential requirement which cable should be connected first except AC adapter, it is strongly recommended connecting the AC adapter as the last step when finish all the connection. *For Macintosh users: The connector or cable requirements may be different, the ENXTV-X2 package does not contain such accessories. Owners may need to get it form the Macintosh store. 2. 4 External Audio/Video input connection When connecting the ENXTV-X2 with the external A/V source such as DVD, VCR or Camcorder and to enjoy the high quality visual / sound entertainment, please turn off the power and make the correct connection as the diagram indicated below. Chapter 3: Using the ENXTV-X2 This chapter shows how to use the ENXTV-X2. 3. 1 PC side VGA resolution setting ENXTV-X2 can be used independent of PC system for a full screen display. In addition to the full screen display, when it is connected in conjunction with the Computer system, the PIP sub video Window can also be displayed at the top of PC monitor screen to let the user watch TV while using the computer at the same time, or just enjoy a full screen TV viewing. . When the ENXTV-X2 is use as a standalone TV box (computer CPU is turned off), it is completely independent with the computer's VGA or monitor screen settings. [. . . ] MENU: When in Full Screen Mode, this key is use for settings. When in PIP Mode, this is use to move the PIP screen in conjunction with the CH+/- keys to move PIP screen high and low, and with the VOL +/- keys to move the PIP screen right and left EXIT: Exit form current Menu setting. PIP: Enter into PIP mode. MODE: When in PIP Mode: MODE key is use to change the PIP screen display size. When in Full Screen Mode: MODE key is use to change the ENXTV-X2 resolution settings. [. . . ]