User manual ENERGY SPEAKER SYSTEMS V22-WM-SK

[. . . ] Reserve the scrim-cloth until the grille is painted and dry. If you are using a spray gun, set it for the most diffuse spray and try two very thin coats. If you are using a brush, thin the paint so that the grille holes will not be blocked. After the paint is dry, apply four or five small, thin spots of spray adhesive (similar to 3M Super 77) around the edge of the scrimcloth. [. . . ] However, the NCB-L-WM (New Construction Brackets) are bulk packed, four brackets in each carton. Optional - NCB-L-WM "Hole Saver" The NCB is never installed when fitting a speaker into an existing wall. It MAY be installed during a remodel or the construction of a new house, while the structural joists and studs are exposed. Typically, the wire is placed now, to avoid electrical wires (they can cause hum). The NCB is simply nailed between the studs and locked into position with screws. The intalled NCB forces the wallboard installer to cut the hole for the speaker, thus avoiding potential dust and mess. Additionally, it provides a tiedown to the speaker wire and clearly shows everyone where the speaker will be installed, avoiding misunderstandings. Required - API Mounting Kit MK-L-W In new construction, the mounting kit is installed once the wall is covered with drywall or plaster. In a retrofit to an existing wall, the hole is cut and used to facilitate running wire back to the equipment location first, then the mounting kit is installed. Once the hole is cut, before the actual bezel is installed, the Wallbracers are installed above and below the hole to dampen and eliminate distortion caused by sympathetic wall resonance. The included wall insulation packets are opened and two pieces of insulation are installed above the hole and two pieces below the hole. Once the bezel is pushed into the hole, the spring loaded dogs are rotated into place. Now the bezel is ready for the speaker to be installed. For more detail, consult the instructions packed with the kit. Required - V2. 2-WM-SK In new construction, the V2. 2-WM speaker kit is only installed once the house is secure and ready for occupancy. In a retrofit, the speaker kit is installed after the bezel is mounted and before the grille is fitted. The swinging spring loaded dogs ease installtion of the Mounting Kit/ Les brides à ressort d'oscillation soulagent l'installtion du kit de support The patent-pending UltraDamped Mounting System includes both insulation and the unique WallBracers which act together to reduce the distortion caused by drywall resonance. / Le système brevet-en suspens de support d'UltraDamped inclut l'isolation et le WallBracers unique qui agissent ensemble de réduire la déformation provoquée par résonance deplaques de plâtre. Considérations d'Installation Energy Veritas empaquette le V2. 2-WM dans trois cartons séparés. Ceci le facilite pour des installations dans la nouvelle construction, puisque seulement la partie nécessaire est apportée dehors à l'emplacement du travail à chaque étape de construction. Dans une modification à un mur existant, vous devez apporter un kit de haut-parleur de V2. 2-WM-SK et un MK-L-WM pour CHAQUE endroit de haut-parleur. Des haut-parleurs de Energy Veritas et les kits de support sont emballés séparément, pas dans les paires. Cependant, le NCB-L-WM (Supports D'endroit de nouvelle construction) sont emballés en vrac, quatre supports dans chaque carton. Facultatif - "Épargnant De Trou" - NCB-L-WM Le NCB n'est jamais installé en adaptant un hautparleur dans un mur existant. [. . . ] Ajustez les commandes d'égalization comme suit: In-Wall Boundary Compensation / La compensation de frontière de Dans-Mur Quand le haut-parleur est monté à moins de deux pieds d'un coin, mi déformation basse substantielle est créée. Corrigez le problème en plaçant le commutateur dans le "Corner?" placez. Midrange Frequency Equalization /L'égalization de fréquence de mi-portée Écoutez un passage des vocals ou du piano femelles. Si le bruit est trop vers l'avant, abaissez le niveau. [. . . ]