User manual ENGENIUS SN-900 INSTALL GUIDE

[. . . ] If you have any reason to suspect that interference is taking place, turn off your handset immediately. For hands-free operation of the handset, the device has been tested for RF exposure compliance with the EnGenius brand belt-clip and leather pouch. Other belt-clips, holsters or similar accessories that have not been tested may not comply with RF exposure requirements and should not be used. Congratulations! You have purchased an exceptional business communications tool from the leading Industrial Cordless TM Phone System manufacturer. The EnGenius SN-900 ULTRA Industrial Cordless Phone System is the second generation of the Longest Range Cordless Phone and 2-Way Radio system. [. . . ] The handset ID number will be reset to "00" as seen in the middle of the top LCD line. De-Registering a Handset from a Single Base Unit 1. Press and hold the VOLUME and PAGE buttons on the base the handset is to be de-registered from until there is a beep. Press the RIGHT SOFT FUNCTION key to select MENU. Press the "6" key to select the register option. Press the "2" key to select DEREGISTER. The LCD will read: " Dereg from base X " when de-registration is complete. SECURITY FUNCTION: A third option is available for deregistering all the handsets at once and generating a new base ID code (system registration reset). This option can be selected by pressing "MENU", "6", "3", then enter a new base number (1-4). Both the handset and base must be in the registration mode. All handsets registered to this base unit will no longer have access to this base without being re-registered to this base again. Register a Second, Third or Fourth Base Unit NOTE: A handset can be registered to a maximum of 4 base units. All base units that come from the factory are registered as base unit 01. De-Registering a Handset from all Base Units 1. Press the RIGHT SOFT FUNCTION key to select MENU. Press the "1" key to confirm unlocking the keypad. Press 1 to confirm UNLOCK Directory This feature allows you to store up to 30 frequently used telephone numbers (up to 20 digits each) and names (up to 14 characters each) in a directory that resides in the handset memory. Entries in the Phone Directory may be viewed or edited at any time. The Phone Directory may be viewed by pressing the or arrow keys from the idle mode. NOTE: Upon successfully changing the base ID number, the display will say "Base ID = *, Dereg All. " This means that you have successfully created a new identification number for that base unit. All handsets previously registered to that base unit (if any) were de-registered. You may now begin registering handsets to the base unit. Follow steps 3 through 6 of Handset Registration section. ~ 41~ ~ 42~ DIRECTORY VIEW MODE Press "MENU", "2" to access Directory screen 1. To view the Directory from the IDLE mode, press the RIGHT SOFT FUNCTION key to select the MENU option. DIRECTORY EDIT MODE While in the DIRECTORY VIEW mode, the LCD will display the following screen: To enter the DIRECTORY EDIT mode, either ADD or OPTION must be selected. Jane Doe 5551212 ADD OPTION 2. While in the Main Menu, press the "2" key to select DIRECTORY: 3. Information in the Phone Directory is stored vertically, as shown in Table 1 below. The up and down arrow keys are used to move through the directory records. ADD Main Menu: ¡ ¡ õô 1:KEY GUARD 2:DIRECTORY 3:CALLER ID 4:SOUNDS 5:SETTINGS 6:REGISTER * Press the LEFT SOFT FUNCTION key to select ADD. This choice will allow an entry to be added to the Phone Directory. [. . . ] Do not use non-EnGenius charging devices. This could damage the batteries. SAVE THESE SAFETY INSTRUCTIONS ~ 66~ Regulatory Information 1. This telephone system complies with Part 68 of the FCC rules. On the bottom of the base station is a label that contains, among other information, the FCC Registration Number, Ringer Equivalence Number (REN) and the Universal Service Order Code (USOC), which is RJ-11C. [. . . ]