User manual EPOX EP-BX6

[. . . ] There are no jumper setting for CPU Speed Setup but detected automatically through the BIOS. Designed with Intel's 82443 BX AGPset. Supports up to 768MB of SDRAM (minimum of 8 MB) on board, You can use 168-pin DIMM x 3. [. . . ] The onboard PIIX4E chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. Built-in ATX 20-pin power supply connector. Software power-down when using Windows® 95/98. Supports ring-in feature (remote power-on through external modem, allow system to be turned on remotely). Resume by Alarm - Allow your system to turn on at a preselected time. Power Loss Recovery - In the event of a power outage your system will · · · · · · · automatically turn itself back on without user intervention. Supports CPU Hardware sleep and SMM (System Management Mode). Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (optional) Supports Hot key, Any key or password Keyboard power ON function (KBPO). Supports USDM software to allow the status monitoring of various aspects of the system when using Windows® 95/98 or Windows® NT 4. 0. Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode. Supports the onboard standby in suspend green or STR mode LED (D2). Supports the STR (Suspend To RAM) power management by ACPI's S3. Supports the STR indicator red LED (D8) to avoid plugging or un-plugging · · · · · · · · DIMM modules when in a STR mode. Supports the System Power LED (PANEL) blinks in the sleep mode. Built-in WOL (Wake On Lan) Connector. Page 3 Installation BX6 BX6 Detailed Layout Figure 1 Page 4 BX6 Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure Jumpers System memory Configuration Device Connectors Configure Settings The following will describe all of the setting that you are required to set before moving on to step 2. ROM PCI/ISA BIOS(2A69KPAI) SENSOR & CPU SPEED SETTING AWARD SOFTWARE, INC. Auto Detect DIMM/PCI Clk Spread Spectrum Modulated CPU Host Clock CPU/PCI Clk Ratio CPU/AGP Clk Ratio CPU Int Clk Ratio CPU Clk Frequency CPU:AGP (Clk:Clk) CPU:PCI (Clk:Clk) CPU Vio Voltage CPU Vcore Voltage CPU Vcore Voltage : Enabled : Disabled CPU Warning Temperature Extended JP2 Temperature Current CPU Temperature Current System Temperature Current POWER FAN Speed Current CPU FAN Speed Current CHASSIS FAN Speed Vcore : 2. 10V Vtt(V) Vio(V) : 3. 47V +5V +12V : 12. 40V -12V -5V : -5. 50V VBAT (V) 5VSB (V) : 5. 08V Shutdown Temperature : 95OC/205OC : 0OC/32OC : 0OC/32OC : 0OC/32OC : 4900 RPM : 4900 RPM : 4900 RPM : 1. 55V : 5. 02V : -11. 95V : 3. 44V : 100OC/167OC : Default : Auto : Auto : x3 : 300(100x3) MHz : 3:2 (100:66) : 3:1 (100:33) : 3. 40V : +0. 10V : 2. 10V é ê è ç Select Item Esc:Quit : F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift) F2 : Color F7 : Load Setup Defaults Page 5 Installation CPU Type External Clock Ratio 2. 0 2. 5 3. 0 3. 5 4. 0 4. 5 5. 0 5. 5 6. 0 6. 5 7. 0 7. 5 8. 0 BX6 Slot1 Type Pentium II Pentium III Celeron S370+Convert Card 66 or 100 Note: Based on the implementation of the Intel 440BX AGPset, the BX6 is able to provide multiple front side bus (FSB) frequencies for Slot 1 processors and memory operations. The motherboard's FSB is easily se- lected by BIOS Setup listed above to match the FSB required by your processor. When using the 100MHz FSB (or higher) you must use PC100 (or better) compliant SDRAM. [. . . ] Using the SoftOff by Pwr-BTTN feature, you can choose either Instant Off (turns system off immediately), or 4 sec delay (you need to hold the button J3 1 down for 4 seconds before the system turns off). When the system is in 4 sec delay mode, there is a special feature to make the system to go into suspend mode when the button is pressed momentarily. ) Turbo LED indicator - LED ON when higher speed is selected + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks + is activate IR Connector 1. IRTX 1 J2 KeyLock - Keyboard lock switch & Power LED connector 1. [. . . ]