User manual EPOX KP6LS

[. . . ] KP6-LS (SMP) A Dual Pentium® II Processor based AGP motherboard TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. Manual Revision 1. 2 February 10, 1997 KP6-LS Features FEATURES KP6-LS Features: · KP6-LS is based on the Dual Pentium® II Processor operating at 233 ~ 330 MHz on Slot 1. The board is configured by an Easy-Setting-Single-Jumper (E. S. S. J. ) to match your CPU clock speed. · Designed with Intel's 82443 LX AGPset. [. . . ] (http://www. 2themax. com/ please visit our Technical Support section for the latest updates) Page 2 Features KP6-LS · KP6-LS utilizes a Lithium battery which provides environmental protection and longer battery life. · Supports the Universal Serial Bus (USB) connector. The onboard PIIX4 chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. · Built-in ATX 20-pin power supply connector. · Software power-down when using Windows® 95. · Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely. · Resume by Alarm - Allows your system to turn on at a preselected time. · Power Loss Recovery - In the event of a power outage your system will automatically turn itself back on without user intervention. · Supports CPU Hardware sleep and SMM (System Management Mode). · Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (option) Page 3 Installation KP6-LS KP6-LS Detailed Layout Bank 0 Bank 1 PS/2 (Top) Keyboard (Bottom) CPU1 Fan J4 (Top) CPU Cartridge SLOT 1 Primary CPU Cartridge SLOT 1 Secondary (Bottom) Parallel Port COM 2 COM 1 J9 ATX Power Input USB USB 0 USB 1 Intel 443LX PCIset 1 Infrared J2 J1 Chassis Intrusion AGP SLOT PCI Slot #1 PCI Slot #2 JPX1 Wake On-Lan CPU2 Fan J8 J12 1 J11 1 Secondary IDE Primary IDE 33 0M H z 30 0M H z 26 6M H z 23 3M H z 20 0M H z DIMM 1 DIMM 2 DIMM 3 DIMM 4 JP JP JP JP JP7 D e f a u lt Winbond 83977 I/Oset Flash Memory for BIOS PCI Slot #3 PCI Slot #4 ISA Slot #1 ISA Slot #2 ISA Slot #3 Intel PIIX4 PCIset Clear CMOS JP3 Chassis Fan J3 Bank 2 Mouse Bank 3 J14 PW H/D G/L SL TB RS 1 J13 FDD Connector J4 LM79 Hardware Monitor Battery Intel 82093A SP KP6-LS Rev. # KE 1 JP1 Figure 1 Page 4 KP6-LS Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure Jumpers to match your hardware Install memory chips Device Connectors Configure Jumpers 2theMax designs all motherboards with the fewest jumpers to make your install fast and easy. The following will describe all of the jumpers that you are required to set before moving on to step 2. Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation. JP1: 4 6 1 3 BIOS Voltage Setting JP1: = 1-2 - +5V Flash (Default) 4-5 = 2-3 - +12V Flash 5-6 CMOS Clear JP3: = 1-2 - Run Mode (Default) = 2-3 - Clear CMOS JP3: 1 Page 5 Installation 16 15 KP6-LS CPU Processor Selection JP7: = 1-2 - 200MHz = 3-4 - 233MHz (Default) = 5-6 - 266MHz = 7-8 - 300MHz = 9-10 - 330MHz = 11-12 - Reserved = 13-14 - Reserved = 15-16 - Disable E. S. S. J. Reserved CPU Processor Selections JP9: = Reserved JP10: = Reserved JP11: = Reserved JP12: = Reserved JP7: 2 1 JP9: JP10: JP11: JP12: Page 6 KP6-LS Installation System Memory Configuration Memory Layout The KP6-LS supports (4) 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized DRAM). · DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 120MHz (8ns) bus speed. [. . . ] + J4 + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is activate Power Saving LED indicator - LED ON when system is in any power saving mode Sleep/Resume switch : Closed to enter sleep mode, a keystroke or mouse movement will instantly "wake up" the system. + Turbo LED indicator - LED ON when higher speed is selected + Reset - Closed to restart system. 1 Speaker - Connect to the system's speaker for beeping 1. GND KeyLock - Keyboard lock switch & Power LED connector 1. [. . . ]