User manual EPOX P2-133A

[. . . ] · Supports up to 384 Mega of DRAM (minimum of 16 MB) on board, You can use 168-pin DIMM x 3. It will automatically detect Extended Data Output (EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at 66MHz or 100MHz (please see Section 3-2). · P2-133A will support Error Checking and Correcting (ECC) when using paritys DRAM memory modules. This will detect multiple bit errors and correct 1-bit memory errors. · Supports (2) 16 bit ISA slots, (5) 32 bit PCI slots, (1) AGP slot and provides (2) independent high performance PCI IDE interfaces capable of supporting PIO Mode 3/4 and Ultra DMA 33 devices. [. . . ] · Power Loss Recovery - In the event of a power outage your system will automatically turn itself back on without user intervention. · Supports CPU Hardware sleep and SMM (System Management Mode). · Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (optional) · Supports Hot key, Any key or password Keyboard power ON function (KBPO). · Supports USDM software to offer motherboard various status on Windows® 95/98, or Windows® NT 4. 0/5. 0. · Supports the CPU, PWR and Chassis fan Auto stop in sleep mode. · Supports the System Power LED (PANEL) blinks in the sleep mode. · Built-in WOL (Wake On LAN) Connector. · Built-in SB-LINK Header for Creative Blaster® AWE64D PCI Bus Sound Card. Page 2 Installation P2-133A P2-133A Detailed Layout Bank 2 Bank 0 CPU FAN (Bottom) (Bottom) JP13 CPU Cartridge SLOT 1 USB USB 1 (Top) USB 0 Parallel Port COM 2 COM 1 ATX Power Input PS/2 Mouse (Top) Keyboard J4 Bank 1 POWER FAN J5 DIMM 1 DIMM 2 DIMM 3 J3 FDD1 + + POWER_ON Secondary IDE IR CONN. 1 5 KEYLOCK 1 SPK RESET IDE2 IDE1 J2 AGP SLOT Winbond 83977 I/Oset PCI Slot #1 PCI Slot #2 J7:WOL PCI Slot #3 Flash Memory for BIOS Battery PCI Slot #4 PCI Slot #5 J8 SB_Link 1 J6 CHASSIS FAN JP3 12 JP1 ISA Slot #1 ISA Slot #2 25 26 3X 3. 5X 4X 4. 5X 5X 5. 5X AUTO 66MHz 100MHz 103MHz 112MHz 124MHz 133MHz Figure 1 Page 3 ESDJ P2-133A Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure Jumpers to match your hardware Install memory chips Device Connectors Configure Jumpers We design this motherboards with an ESDJ to make your installation fast and easy. The following will describe all of the ESDJ that you are required to set before moving on to step 2. Note: The ESDJ as depicted as shown (Figure 1) in their correct physical orientation. JP 1 1 3 C M O S C lea r JP 1 = 1 -2 - R u n M o d e (D e fa u lt) = 2 -3 - C le a r C M O S (m o m e n ta r ily ) K e y b o a r d P o w e r -O N fu n ctio n (re fe r th e s ec tio n 3 -5 ) JP 13 = 1 -2 - E n a b le d = 2 -3 - D is a b le d (D e fa u lt) W O L (W a k u p O n L a n ) C o n n e c to r R e s e rv ed fo r N I C (N e tw o r k In te rfa c e C a r d ) to W a k e th e S y s te m . S B -L I N K H ea d e r R e s e rv ed fo r C r e a tiv e S B -L I N K (S o u n d B la s te r L IN K ) w ith th e S o u n d B la ste r AW E 6 4 D P C I S o u n d C a r d to C o m p a tib le D O S g a m e s a n d M u ltim e d ia a p p lica tio n s. TM TM JP 13 1 3 J7 J8 Page 4 Installation P2-133A * * * * * ** Note: Based on the implementation of VIA Chipset Apollo Pro+, P2-133A is able to provide two host bus frequencies -- either 66 or 100MHz for Slot1 processor and memory operating. The default is set at 100MHz once Pentium® II processor to be mounted onto this motherboard. However, no matter what kind of Slot1 processor you installed, it should come with right memory modules for normal and stable operation. For example, if you install a Deschutes processor, you should use the SDRAM module with 100MHz based(or above) to match the CPU speed. Furthermore, one thing you may need to bear in mind, before the CPU installation, it is anyway our advice to use JP3 and set up right speed of Slot1 processor at any time. Page 5 P2-133A Installation System Memory Configuration Memory Layout The P2-133A supports (3) 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized DRAM). [. . . ] GND KeyLock - Keyboard lock switch & Power LED connector 1. GND system is powered on and blinks in SLEEP MODE (Suspend mode). J3 1 IR Connector 1. IRTX + + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is activate Turbo LED indicator - LED ON when higher speed is selected Power On/Off - This is connected to the power button on the case. [. . . ]