User manual EPSON ACULASER CX16NF

[. . . ] User's Guide NPD4213-01 EN AcuLaser C1600 User's Guide Copyright Notice No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S. ) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. [. . . ] Align the shaft on each end of the toner cartridge with its holders, and then insert the cartridge. Note: Before inserting the toner cartridge, make sure that the color of the toner cartridge to be installed is the same as the label on the toner cartridge carousel. Replacing Consumables 43 AcuLaser C1600 User's Guide Note: Do not touch the contact indicated in the illustration. 9. Press in the toner cartridge until it locks into place. 10. Close the front cover. Replacing Consumables 44 AcuLaser C1600 User's Guide Note: To replace the toner cartridge for another color, after the front cover has been closed, check that the indicator for the toner to be replaced is lit (if necessary, press the Rotate Toner key), and then replace the toner cartridge as described in steps 2 through 10. Press the Clear key to reset the printer and clear the indicator message. Note: The printer must complete a calibration cycle after a toner cartridge has been replaced. If you open the top or front cover before the printer is reset, the calibration stops, then starts over again after the cover is closed. Removing All Toner Cartridges Note: Be careful not to spill toner while replacing a toner cartridge. If toner spills, immediately wipe it off with a soft, dry cloth. By using the Eject All Toner mode, all toner cartridges can be removed. Follow the procedure described below to use the Eject All Toner mode. Use either operation described below to switch the printer to Eject All Toner mode. Hold down the Rotate Toner key for more than 10 seconds. On the Panel tab of the Remote Panel Program, select Eject All Toner, and then click the Rotate Toner button. Note: The printer enters Eject All Toner mode, and the magenta toner indicator lights up. To exit Eject All Toner mode, press the Clear key. Replacing Consumables 45 AcuLaser C1600 User's Guide 2. Pull down the handle on the toner cartridge until the toner cartridge is unlocked and moves out slightly toward you. Remove the toner cartridge. Replacing Consumables 46 AcuLaser C1600 User's Guide Note: Do not manually rotate the toner cartridge carousel. In addition, do not rotate the carousel with force, otherwise it may be damaged. Note: Do not touch the contact indicated in the illustration. 4. Follow the same procedure to replace the cartridges for the cyan, black, then yellow toners. Press the Clear key. Replacing the Photoconductor Unit Part Name Photoconductor Unit Photoconductor Unit Part Number 1198 Note: For optimum print quality and performance, use only the corresponded TYPE genuine Epson photoconductor unit. Replacing Consumables 47 AcuLaser C1600 User's Guide 1. Open the top cover. Note: If there is paper in the output tray, remove it, and then fold up the output tray before opening the top cover. Grab the handle and lift it up slightly to the back, and then slowly pull the photoconductor unit out vertically. Note: Dispose of the used photoconductor unit according to your local regulations. [. . . ] Remove the photoconductor unit and check for damage. If it is damaged, replace it. Abnormal areas (white, black, or color) appear in a regular pattern. The print head window is dirty. The photoconductor unit is defective. Clean the print head window. Remove the toner cartridges with the color causing the abnormal image. [. . . ]