User manual EPSON C82364 NETWORK ADMINISTRATOR'S GUIDE

[. . . ] User's Guide Update Notice for C82363V/C82364V Users Use a shielded twisted-pair cable (Category-5) to connect the interface card, otherwise the interface card may malfunction. For C82363V Users The C82363V Ethernet card also has a DC power connection. You can connect the C82363V Ethernet card to the following EPSON printers using AC adapter C82525V (Model EU-30); EPSON Stylus COLOR 800/850 FX-880/ 1100/ 2170 DFX-8500 LQ-670/ 2070/ 2170 DLQ-3000+ Before connecting, change the power select switch on the board to the "A" position. For Microsoft Windows 98 Users Y Y The EPSON Net!2 for Windows can be used with Windows 98. Follow the instructions for Windows 95 in the Administrator's Manual. If you are using a NetWare printer, EPSON Status Monitor 2 utility is not available. [. . . ] The IP Address Configuration and AppleTalk Configuration dialog box appears. Note: See "Setting the IP address for EPSON Net!2 for Windows/ Macintosh" in Chapter 3 for more information about setting the IP address. Set the following options in the AppleTalk Configuration box. Printer Setting: Printer Name: Type the printer name (up to 31 characters). (Printer name)-(last 6 digits of the serial number) Entity Type: If you are using a Level 2 printer, you do not have to set these options. It just shows the printer's Entity type on an AppleTalk network. If you are using a Level 1 printer, set the Entity type to match the printer driver for the printer with the Ethernet card. 5-4 Using the Ethernet Card with Macintosh AppleTalk Setting: Zone Name: Select the network zone in which you want the printer to appear. If the zone has not been set, "]" appears. Network Number Set: Select the network number setting. Network Number for Manual Mode: The default number is 65535. If you have selected Auto for the Network Number Set, you cannot type the network number manually. Note: If you cannot see the printer in the Chooser, check whether any AppleTalk routers have been set incorrectly. If you cannot change the router settings, select Manual for the Network Number Set and type a network number in the Network Number for Manual Mode box as a temporary solution. In this case, you must type the correct zone and the network number of the zone. If you do not make this setting correctly, you cannot configure the Ethernet card for use with the Macintosh. Try one of the following: o o o 5 Start the browser from EPSON Net!2 for Windows and configure the Ethernet card again. Configure the Ethernet card using EPSON Net!2 for Intranet (TCP/IP must be set correctly). Click the Send button to save the new settings to the Ethernet card. If the message "Configuration is successfully done" appears, updating is complete. Using the Ethernet Card with Macintosh 5-5 Configuring the Ethernet Card for AppleTalk Using EPSON Net!2 for Intranet You can use EPSON Net!2 for Intranet after setting the IP address of the Ethernet card, as describes in Chapter 3. c Caution: o You cannot use EPSON Net!2 for Macintosh and EPSON Net!2 for Intranet at the same time. o Once you make changes to the Ethernet card using EPSON Net!2 for Intranet, wait until it completes the settings before turning off or sending data to the printer. Note: q If you have not assigned the IP address or if you use the default setting (included when you select DHCP to acquire an IP address) with EPSON Net!2 for Macintosh, you cannot set the IP address for the Ethernet card using EPSON Net!2 for Intranet. q See the previous section "Configuring the Ethernet Card Using EPSON Net!2 for Macintosh" for the cautions and notes for each step. There are some restrictions on the characters you can use depend on your browser. For details, see your browser or OS manual. q 1. Click the printer you want to configure from the list, and click the Launch Browser button. Or, run the browser and type the IP address for the Ethernet card. [. . . ] To confirm the ROM version number, print a status sheet and make sure the first four numbers of the Firmware Revision number are 7717 or higher. See Chapter 1 on page 1-2 for information on how to print a status sheet. Contact your dealer and purchase a ROM update if necessary. An application error occurs, and NetWare printers cannot be monitored when Allow monitoring is selected for monitoring Windows shared printers under Windows NT 4. 0. Cause What to do There is a known bug in the operating system. Install Service Pack 2 or higher before monitoring Windows shared printers under Windows NT 4. 0. 12-10 Troubleshooting NetWare printers cannot be monitored when Allow monitoring is selected for monitoring Windows shared printers under Windows NT 3. 51/ 4. 0. Cause What to do Because of the specification of EPSON Status Monitor 2. Double-click Services in the Control Panel and stop the EPSON Printer Status Agent service. Restart EPSON Status Monitor 2 and then restart the service. [. . . ]