User manual EPSON EB-570 INSTALLATION GUIDE

[. . . ] Installation Guide Guide d’installation Guía de instalación Español Français English Using the Product Safely Safety Instructions For your safety, read all the instructions in this guide before using this product. Incorrect handling that ignores instructions in this guide could damage this product or could result in personal injury or property damage. Keep this installation guide at hand for future reference. Read the User's Guide and Safety Instructions for your projector and follow the instructions in these documents. [. . . ] These will be the basis for determining the mounting position of the wall plate. € Height ( • Center line ( ) of the distance (c) between the top edge of the projected image and the wall plate ) of the projected image 29 Installation Guide b Attach the template sheet to the wall • Match the center line ( ) checked in step 1 to the Image Center line on the template sheet. Confirm where the beams are within the wall, and shift the position left or right as necessary. (The position can be shifted horizontally left or right from the center line of the projection surface up to a maximum of 45 mm. ) • Match the height ( ) checked in step 1 to the line on the template sheet. [Unit: mm] c Determine the positions for the mounting holes for the wall plate Secure the wall plate in at least three points. € If securing the wall plate in four places, make the holes indicated by A or B in the figure. € If securing the wall plate in three places, make the holes indicated by C in the figure. Four mounting holes Three mounting holes 30 Installation Guide d Drill the holes in the wall Drill diameter: 10. 5 mm Pilot hole depth: 45 mm Anchor hole depth: 40 mm e Remove the template sheet, and clean the concrete dust from the holes with a dust pump f Position the wall plate on the wall and insert M10 x 60 mm commercially available anchors into the holes Attach the nut and tap it with a hammer until the core touches the top of the an‐ chor. G Tighten the nut with a commercially available spanner to secure the wall plate to the wall Determine the projection distance, and then pass the cables through the setting plate a Check the following values in the projection distance table • Numbers on the arm slide scale (b) • Distance from surface of screen to wall (x) s "Projection Distance Table" p. 11 31 Installation Guide b Loosen the M4 bolts (x2) and extend the arm slide on the setting plate Align the slider with the combined distances of (b) and (x) that you checked in step 1. C Route the necessary cables through the setting plate See the following figure to route the cables so that the ends of the cables that connect to the projector are on the projector's interface side. Warning Do not hang the rest of the cable over the setting plate. 32 Installation Guide Attaching the setting plate to the wall plate a Insert the hexagonal axis into the setting plate b Mount the setting plate to the wall plate Insert the top of the hexagonal axis into the wall plate, and then insert the M8 bolt into the slot at the bottom. Caution Take care not to trap the cables between the setting plate and wall plate. 33 Installation Guide c Secure the setting plate and the wall plate Secure the supplied M6 screws (x3) with a commercially available No. 3 cross-head screwdriver, and then lightly tighten the supplied M6 bolt (x1) with the spanner. D Adjust the vertical slide with the open-ended spanner, and align it with the standard ) position ( • Tightening the hexagonal axis at the top ( • Tightening the M8 bolt at the bottom ( ) raises the setting plate, and loosening the axis lowers it. ) lowers the setting plate, and loosening the bolt raises it. 34 Installation Guide e Tighten the M6 bolt (x1) to fix the setting plate in position Securing the projector to the setting plate a Loosen the screws (x2) and remove the cable cover from the projector b Insert the slide plate into the setting plate from the interface side of the projector 35 Installation Guide c Align the 3-axis adjustment unit with the slide plate's standard position ( ( ) indicates the screw holes for the bolts. ) d Tighten the supplied M4 bolts (x2) e Connect the cables to the projector 36 Installation Guide c • Connect the power cord last. [. . . ] Bin) that you saved to your computer to the toplevel folder of the removable disk c Do not copy any files or folders other than the batch setup file to the removable disk. E Perform "Remove USB device" on your computer, and then disconnect the USB cable c When using OS X, perform "Remove EPSON_PJ". When all of the indicators start flashing, the settings are being written. Caution Do not disconnect the power cord from the projector while the settings are being written. [. . . ]