User manual EPSON EMP-7200 annexe 1

[. . . ] You can use the on the projector's control panel to correct keystone distortion. See page 7. To store the extended front feet, pull up the foot adjust lever and then slowly lower the front panel. Becomes higher Adjusting the image size and focus Projection position adjustment (up/down) Image size adjustment Focus adjustment Automatically adjusting computer images to the optimum settings Press on the operation panel or open the cover on the remote control and press automatically adjust the tracking, the display position and the synchronization. to 6 Projector Remote Control Other adjustments Press on the operation panel or open the cover on the remote control and press to display the setting menu on the projection screen. Then adjust the required settings, such as brightness, contrast and sharpness. Using the on-screen menus Menu screen Projector panel operations Move up Return Move left Remote control Select /Execute Move up Move left Move right Move right Select/Execute Move down Move down Return Projector Remote Control Adjustment / Turning Off the Projector Adjustment Correcting keystone distortion Page 38 of Owner's Manual If the images have keystone distortion . . . Keystone Press on the projector's control panel to correct the keystone distortion. 7 Tip When keystone correction is carried out, the projected image will become smaller. The trapezoid correction state is recorded in memory. [. . . ] The trapezoid correction state is recorded in memory. Please readjust it when the projection angle is changed. If the images become uneven in appearance after keystone correction is carried out, decrease the Sharpness setting. Keystone Projector When the top area is spread open. Keystone When the bottom area is spread open. Keystone Turning Off the Projector Page 35 of Owner's Manual 1 Turn off the power for the equipment connected to the projector. Power 8 2 Press the Power twice to turn off the projector's power. Press once to display the confirmation message in order to prevent miss-operations. Power Press it once more to switch off the power supply. It is possible to switch off the power supply by pressing The twice consecutively. will start flashing orange. (Cool-down in progress) 3 Check that the is lit steadily with an orange color, and then disconnect the power cord. If the power cord is disconnected while the is still flashing orange, it may cause problems with projector operation. * Set the R/C switch on the remote control to the OFF position. (Operation Indicator) Adjustment / Turning Off the Projector Functions for Enhancing Projection Wireless mouse Effect E-Zoom A/V Mute This projector is equipped with a variety of useful functions for enhancing projection. Refer to the corresponding pages of the Owner's Manual for details on each function. 9 Tip The following connections are required to use the remote control as a wireless mouse. Using the remote control for one-person presentations The remote control can be used to carry out the same functions as left-clicking and right-clicking mouse buttons on a computer. You can use the remote control to control the computer's mouse pointer from a distance. Mouse pointer movement Mouse/USB port Mouse cable (accessory) Main cable (accessory) Computer 1 Computer 2 /Component Video R/Cr/Pr G/Y B/Cb/Pb H/C Sync V Sync Tilt the in the direction you Mouse Remote Mouse/Com Audio S-Video S-Audio/Audio2 Video L-Audio-R want the mouse pointer to go. Monitor Out Stack Out Mouse/Com port Depending on the mouse in use, it is necessary to use the supplied mouse cable that is supported by the mouse. Use the USB mouse cable if you are connecting to the computer's USB port. If a mouse cable other than a USB mouse cable is connected while the power supply is switched on, it may result in malfunctions or damage. Mouse clicks Computer 1 Computer 2 /Component Video R/Cr/Pr G/Y B/Cb/Pb H/C Sync V Sync Remote Mouse/Com Audio S-Video S-Audio/Audio2 Video L-Audio-R Monitor Out Stack Out Mouse For left clicks: Press For right clicks: Press Effect function Page 48 of Owner's Manual Enhancing presentation materials Press . :Select :Enter :Return :Exit 4 The selected item will appear on the screen. Checking the indicators Page 70 of Owner's Manual The projector is equipped with indicators that alert you to problems with projector operation. The following tables show what the indicators mean and how to remedy problems that they indicate. 14 Lamp Indicator Indicator status Problem and remedy Lamp error. Remove the lamp and check if it is broken. If the lamp is not broken, reinstall it. If the lamp is broken, replace it with a new lamp. *2 Nearing the time for replacing the lamp. *2 The power has not been switched on or normal projection is in progress. Operation indicator Lamp indicator Temperature indicator Blinking in Red Blinking in Orange Extinguished Operation Indicator Indicator status Illuminated in Orange Temperature Indicator Problem and remedy Indicator status Problem and remedy Excessive internal temperature (overheating). The lamp goes off automatically and projection becomes impossible. Wait for approximately 5 minutes with the projector in that state. After 5 minutes has passed, pull out the power plug and re-insert it. [. . . ] Wait for approximately 5 minutes with the projector in that state. After 5 minutes has passed, pull out the power plug and re-insert it. After re-inserting it, press the and turn on the power again. Power Standby condition. This is the only time when the power cord can be disconnected. [. . . ]