User manual EPSON EMP-82

[. . . ] User's Guide (this manual) This User's Guide contains information on installing the projector, basic operations, using the configuration menus, troubleshooting and maintenance. Notations used in this User's Guide General information Indicates procedures where personal injury or damage to the projector may occur if the procedures are not followed correctly. Indicates additional information and points which may be useful to know regarding a topic. Indicates a page where useful information regarding a topic can be found. Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. [. . . ] Image is truncated (large) or small Only part of the image is displayed. p. 37 Projection stops automatically p. 38 Problems when projection starts Power does not turn on p. 38 Other problems No sound can be heard or the sound is faint p. 38 The remote control does not work p. 39 Problems relating to images No images appear Have you pressed the [Power] button?Is a video signal being input? Press panel. on the remote control or on the projector's control Disconnect the power cable and then reconnect it. p. 14 Check the circuit breaker to see if power is being supplied. Press on the remote control to cancel the A/V mute. Check that the power for the connected equipment is turned on. If the "Message" menu command has been set to "ON", messages relating to the image signals will be displayed. "Setting" - "Display" - "Message" p. 30 If a composite video or S-Video signal is being input If projection does not occur when the "Video Signal" menu command is set to "Auto", select the signal format that matches the signal source. "Setting" - "Input Signal" - "Video Signal" p. 30 Are the image signal format settings correct? 34 Problem Solving Are the image signal format settings correct? If the signal source is connected to the [InputA] port Use the "Input Signal" menu command to set the signal format that matches the signal that is being projected from the connected equipment. "Setting" - "Input Signal" - "Input A" p. 30 You can also press on the remote control to select the format. p. 15 If the VCR or DVD equipment is connected using an RGB SCART adapter Press to set the signal format to "RGB-Video". p. 15 When still no images appear and the DVD equipment is connected, change the setting at the DVD equipment to RGB output. Have the configuration menu settings been made correctly? Try resetting all of the current settings. p. 31 If the connection is made while the power is already turned on, the Were the projector and computer connected while their function (Fn) key that switches the computer's video signal to power was already turned on?p. 10 Decrease the projection angle to reduce the amount of keystone correction. p. 17 If the projector is suddenly taken from a cold environment to a warm environment or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room approximately one hour before it is to be used. If condensation forms on the lens, turn the power off and wait for the condensation to disappear. Is the keystone adjustment value too large?Has condensation formed on the lens? Interference or distortion appear in images Are the image signal format settings correct? If a composite video or S-Video signal is being input If projection does not occur when the "Video Signal" menu command is set to "Auto", select the signal format that matches the signal source. "Setting" - "Input Signal" - "Video Signal" p. 30 If the signal source is connected to the [InputA] port Use the "Input Signal" menu command to set the signal format that matches the signal that is being projected from the connected equipment. "Setting" - "Input Signal" - "Input A" p. 30 You can also press on the remote control to select the format. p. 15 Are the cables connected correctly?Is an extension cable being used? Check that all of the cables required for projection are securely connected. p. 12 If an extension cable is used, interference may increase. Try connecting a signal amplifier. 36 Problem Solving Have the "Sync. [. . . ] 10 SDTV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Selecting the image source. . . . . . . . . . . . . 6, 7, 15 Selection menu. . . . . . . . . . . . . . . . . . . . . . 15, 18, 20, 22 Setup Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]