User manual EPSON EMP-S1H

[. . . ] User's Guide "List of Configuration Menu Commands" 3 Turn on the power for the input source. Simple! Automatic focus will operate when projection starts. You can also switch the projector so that Quick Setup is run. User's Guide "List of Configuration Menu Commands" (While automatic focus is running) For video equipment, press the [Play] button. When projection starts, the automatic focus function will operate to automatically adjust the focus of the projected images. A screen such as the one shown left will appear while adjustment is in progress, but this is normal. Simple! The projected images can be easily adjusted to the optimum images using only these buttons on the control panel. If necessary, press and zoom buttons to make fine adjustments to the image size. [. . . ] The Auto "V-Keystone" function will operate when the projector is tilted. To retract the front adjustable foot, gently push down on the projector while pulling the foot adjust lever. User's Guide "Adjusting the Position and Size of the Projection Area" If tilted horizontally, adjust using the left and right rear adjustable feet. Rear adjustable foot Extend Retract If the height of the images is reduced after vertical keystone correction, run Quick Setup as described on the next page, or adjust the height manually using the following procedure. For adjustment using the configuration menus: "Setting" - "Keystone" -"H/V-Keystone" "Horz. /Vert. /Height" - "Height" User's Guide "Manually Correcting Projection Area Distortion" 6 Attractive images easily, at a single touch The following adjustments are carried out automatically at a single touch. Focus adjustment (Automatic Focus) Keystone correction (Auto Quick Corner) This automatically corrects distortion of the projection area that occurs when the projector is tilted, so that images are projected at an aspect ratio of 4:3. If using a screen (4:3) for projection, this function can be used so that the projection area exactly fits the size of the screen. 1. "The Quick Setup is in preparation. " will be displayed. Simple! Focusing and keystone correction will be complete after is pressed. You can also use this function together with the Wall Shot function. User's Guide "List of Configuration Menu Commands" 2. Adjustment of the projection area will start. While the adjustment is in progress, the screens left will be displayed to measure conditions of the projection surface. (While automatic focus is running) (While Auto Quick Corner is running) If projecting onto a screen, whiteboard or blackboard, adjust the projection area so that it fits within the edges of the screen or board. Be sure to adjust so that the top edge of the screen is inside the projection area. The configuration menu lets you make settings such as startup operations and brightness and tint adjustments. Display User's Logo Projector ID Projection Operation Network* Standby Mode COM Port Language Reset Extended During computer or During S-Video or component video input composite video input EasyMP (EMP-S1H only) All Reset Lamp-Hours Reset Reset Info Lamp Hours (High Brightness) Lamp Hours (High Brightness) Lamp Hours (High Brightness) (Low Brightness) (Low Brightness) (Low Brightness) Source Source Source Input Signal Video Signal Resolution Refresh Rate Sync Info *EMP-830 only 13 Reading the Indicators The projector is provided with indicators to notify you of the projector operating status. The following tables show what the indicators mean and how to remedy the problems that they indicate. Indicates the operating status of the projector Indicates the lamp status Indicates the internal temperature status User's Guide "Reading the Indicators" If all indicators are switched off, check that the power cable is connected correctly and that power is being supplied normally. When the Power indicator is lit/flashing red Red Red Red Red Red Problem/Warning lit flashing off Disconnect the power cable from the electrical outlet. Then contact your dealer or the nearest address provided in the "International Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet. Internal error Red Red Fan related error/ Sensor error Check if the lamp is broken. Disconnect the power plug from the electrical outlet and wait for the lamp to cool down sufficiently (takes about one hour) before checking. p. 16 Lamp open error Lamp timer failure Lamp out Lamp cover is open If the lamp is not broken Replace the lamp and then turn the power on. If the lamp still does not turn on, replace it with a new lamp. If the problem is still not solved after the lamp is replaced, stop using the projector and disconnect the power cable from the electrical outlet. Then contact your dealer or the nearest address provided in the "International Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet. If the lamp is broken Contact your local dealer for further advice. 14 Red Red Internal temperature error (overheating) The lamp will switch off automatically and projection will stop. Then disconnect the power cable and check the points to the right. If you continue using the projector and the temperature rises again, the lamp will switch off automatically. Check the points to the right. Red Orange High-speed cooling in progress If the projector is close to a wall, move it away from the wall. Clean the air filters if they are blocked. If the problem is not fixed, stop using the projector and disconnect the power plug from the electrical outlet. Then contact your dealer or the nearest address provided in the "International Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet. If the Lamp indicator is flashing orange Lamp replacement notification Warning lit flashing off Orange The lamp is near the end of its operating life. [. . . ] · This product includes a lamp component that contains mercury (Hg). Please consult your state and local regurations regarding disposal or recycling. Do not put in the trash. Reset the lamp operating time as described in the following section. Resetting the lamp operating time After replacing the lamp, be sure to reset the lamp operating time from the configuration menu. Do not reset the lamp operating time except after the lamp has been replaced. If you do, the lamp operating time will no longer be displayed correctly. 1. [. . . ]