User manual EPSON EMP-S4

[. . . ] Recommended distance : 0. 9 ­ 11. 3 m (2. 9 ­ 37. 0 ft. ) While referring to the table below, position the projector so that the images are projected at the optimum size. The values should be used as a guide for setting up the projector. The actual values will vary depending on projection conditions and the zoom setting. 4:3 Screen size (cm (in. )) 30" (61 × 46 (24. 0 × 18. 1)) 40" (81 × 61 (31. 9 × 24. 0)) 60" (120 × 90 (47. 2 × 35. 4) 80" (160 × 120 (63. 0 × 47. 2)) 100" (200 × 150 (78. 7 × 59. 1)) 200" (410 × 300 (161. 4 × 118. 1)) 300" (610 × 460 (240. 2 × 181. 1)) Projection distance (m (ft. )) 0. 9 ­ 1. 1 (2. 9 ­ 3. 6) 1. 2 ­ 1. 5 (3. 9 ­ 4. 8) 1. 8 ­ 2. 2 (5. 9 ­ 7. 3) 2. 4 ­ 3. 0 (7. 9 ­ 9. 8) 3. 0 ­ 3. 7 (9. 9 ­ 12. 3) 6. 1 ­ 7. 5 (19. 9 ­ 24. 6) 9. 1 ­ 11. 3 (29. 8 ­ 37. 0) Distance from center of lens to bottom edge of screen (cm (in. )) 4. 3 (1. 7) 5. 8 (2. 3) 8. 6 (3. 4) 11. 5 (4. 5) 14. 4 (5. 7) 28. 8 (11. 3) 43. 1 (17. 0) Setup 3 Screen 90º * Centre of lens * When installing against a wall, leave a space of about 20 cm (7. 9 in. ) between the projector and the wall. The image size will be reduced when keystone correction is carried out. Setting-up Methods The projector supports the following two different projection methods, allowing you to choose the best method for displaying your images. After setting up the projector, refer to the User's Guide for details on turning on the power and adjusting settings such as the screen size. [. . . ] After setting up the projector, refer to the User's Guide for details on turning on the power and adjusting settings such as the screen size. ("Basic Operations" in User's Guide) Before setting up the projector, be sure to first read the separate Safety Instructions/World-Wide Warranty Terms. Front projection Rear projection using a translucent screen When using rear projection using a translucent screen, set the "Rear Proj. " command in the "Advanced" menu to match the installation method. ("Advanced" menu in User's Guide) 4 Continued 3 Connecting to a Video Source 5 When connecting the projector to other video sources, take the following precautions. Turn off the power for both the projector and the video source before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result. If you select either port when image signals are being input from both the Video port and the S-Video port, unevenness may appear. Turn off the power for the video source that is not projected. This manual and the separate User's Guide use the term "video equipment" to refer to devices such as the following that are equipped with video output ports. If you try to force a connector to fit a device port with a different shape or number of terminals, damage to the connector or port may result. The projector cannot be connected to some types of computer, or projection of images may not be possible even if actual connection is possible. Make sure that the computer you intend to use satisfies the conditions given below. Condition 1: The computer must have an image signal output port. Check that the computer has a port such as an "RGB port", "monitor port" or "CRT port" which can output image signals. If the computer has a built-in monitor, or if using a laptop computer, it may not be possible to connect the computer to the projector, or alternatively you may need to purchase a separate external output port. Refer to the documentation for your computer under a heading such as "Connecting an external monitor" or similar for further details. Condition 2: The display resolution and frequency of the computer must be listed in the "List of Supported Monitor Displays". ("Appendices: List of Supported Monitor Displays" in User's Guide) Some computers allow you to change the output resolution, so if necessary, change the resolution to one that matches a setting in the "List of Supported Monitor Displays", while referring to the documentation provided with the computer. You may need to purchase a separate adapter depending on the shape of the computer's port. [. . . ] Condition 2: The display resolution and frequency of the computer must be listed in the "List of Supported Monitor Displays". ("Appendices: List of Supported Monitor Displays" in User's Guide) Some computers allow you to change the output resolution, so if necessary, change the resolution to one that matches a setting in the "List of Supported Monitor Displays", while referring to the documentation provided with the computer. You may need to purchase a separate adapter depending on the shape of the computer's port. Refer to the documentation provided with the computer for further details. [. . . ]