User manual EPSON EMP-TW700

[. . . ] OS* CPU 98SE/Me/NT4. 0/2000 Professional/XP Home Edition/XP Professional Pentium MMX 166 MHz or higher (Pentium II 233 MHz or higher recommended) 64 MB or more (128 MB or more recommended) 6 MB or more XGA (1024×768) or higher resolution, 16 bit or higher display colour Projector A Turn on projector B EMP Monitor Projector B Memory capacity Free hard disk space Display Before starting operations Projector C Check the following points before starting up EMP Monitor. · EMP Monitor must be installed in the computer to be used for monitoring and control. · The computer and the projectors must be connected to the network. · If using Windows 2000, NT4. 0 or XP, the computer must be started up in Administrator mode. [. . . ] Select the projector(s) to be registered, and then click [Add]. You can select several projectors at the same time. If a projector does not appear in the list, use "Registration using IP address (Manual registration)". sp. 6 · Projectors that have been registered using automatic detection will be re-detected on the basis of projector name and the IP addresses for these projectors will be displayed each time EMP Monitor is started. · If a password entry screen is displayed, enter the password for the projector's Administrator and then click [OK]. If more than one projector was selected, the password entry screens for each projector will be displayed in succession. 3 Click [Close] to return to the main EMP Monitor window. Refer to "Main EMP Monitor window" for details on using the main window. sp. 8 Registering projectors for monitoring 6 Registration using IP address (Manual registration) PROCEDURE When using EMP-81/61 The following "Manually register projector" window will be displayed. Complete the form and click [Confirm]. Projector name Enter the projector name of up to 16 alphanumeric characters, from 0 to 9 and from A(a) to Z(z) and - . Enter the port number. 1 2 Click [Manual registration] in the [Register projector] dialogue box. Enter the IP address for the projector to be registered in the [IP address] box, and then click [Confirm]. Power on and normal status Power off and normal status Power on and abnormal status Power off and abnormal status Network error (such as not connected to network or power cord not connected) Name: Shows the projector name. Source: Shows the selected image source. Computer, Computer1 or InputA Computer2 or InputB S-Video Video D4 (Digital) DVI or HDMI (Digital) Error information: Uses the following icons to show the status if an error occurs with a projector. s"Replacing the Lamp" End of lamp life warning in the "Replacing Consumables" section of the accessory User's Guide. "Reading the Indicators" Lamp problem sRefer to the High internal temperature "Troubleshooting" section (overheating) of the accessory User's Guide and carry out the Temperature warning suggested remedy. Internal problem Fan problem Temperature sensor problem The projector information that is generated when a problem is detected is stored until EMP Monitor is closed. The EMP Monitor displays will not be updated automatically even if the projector status returns to normal. Click [Refresh] in the main window to update the status. Main EMP Monitor window 10 Displaying detailed information You can check detailed information on the status of individual projectors that are connected. PROCEDURE 1 2 Select the projector to be checked in the main window. Click [View details]. Click to display details. The details that are displayed may vary slightly depending on the projector connected. Detailed status information will be displayed in the [Details] dialogue box. A projector cannot be monitored or controlled using EMP Monitor Cause Remedy Is the projector connected to Connect the network cable correctly. s"Network Cable Connections" in the accessory User's Guide Has the projector been set Check the settings for the "Network" up correctly for connection configuration menu command. sAccessory User's Guide Has EMP Monitor been Uninstall EMP Monitor and then re-install installed to the computer it. [. . . ] sAccessory User's Guide 11 Appendices When using EMP-81/61, you need to make a setting for the adapter. Make the setting as shown in the following table. Menu Port Properties Main Item Serial Port Settings Sub Item Serial Protocol Speed Character Size Parity Stopbit Flow Control UDP Datagram Mode UDP Datagram Type Response Port Password Telnet Mode Inactivity Timeout Port Password Encryption Twofish Key Setting UDS100 UDS200 RS232 9600 8 None 1 None Disable (Blank) Nothing (quiet) Disable Disable Enable (Blank) ­ ­ Disable (Not selectable) (Blank) 12 Connect Mode Settings Additional Settings Security Security Settings 13 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. [. . . ]