User manual EPSON EPL-5700I INSTALL GUIDE

[. . . ] Contents Introduction Unpack the Printer Attach the Paper Tray Connect the Printer Install the Software For Macintosh For Windows 98 with USB Connection For Windows with Parallel Connection Print a Test Page System Requirements Safety Instructions Additional Precautions Where to Get Help 1 2 4 6 8 8 12 16 18 19 20 26 28 Introduction Follow each of these steps in this guide to get your EPSON EPL-5700i up and running: 1 Unpack the Printer 2 Attach the Paper Tray 3 Connect the Printer 4 Install the Software Also be sure to check the System Requirements and follow all the Safety Instructions in the back of this guide. See your Reference Guide for detailed information on using your printer. 1 Step 1 Unpack the Printer 1 Unpack the printer from its box and check for these items: EP SO N ® EP 0 70 L-5 i EP SO N ® EP 0 70 L-5 i Se tup Gu ide Re fer en ce Gu ide Make sure you have a USB or parallel cable to connect the printer to your computer. Printer Software CD-ROM power cord Setup Guide Reference Guide printer paper tray developer cartridge and photoconductor unit (both already installed) 2 Remove these two strips of tape: 2 3 Pull the tab straight out as shown below. Lift the front edge of the printer and pull firmly to remove Be sure to check for other tape or packing material, which may be in slightly different locations on your printer. the tab. 4 Place the printer near your computer and an available grounded outlet, but avoid areas: · · · with high temperature or humidity in direct sunlight or dusty conditions near sources of heat or electromagnetic interference, such as the base of a cordless telephone 3 Step 2 Attach the Paper Tray 1 Remove any protective tape you see on the paper tray. Then lift off the cover and set it aside. 2 Insert the paper tray into the printer as shown. Push it all the way in until it locks. paper guides paper tray 3 Slide the blue paper guides apart. Then load a stack of paper (no more than 150 sheets). 4 4 Place the cover on the paper tray. 5 Raise the output tray extension until you feel it lock. 5 Step 3 Connect the Printer 1 Make sure the printer and computer are turned off. CAUTION 2 Plug the power cord into the back of the printer. Then plug the other end into a grounded electrical outlet. Avoid using outlets on the same circuit with large motors or other major appliances that might disrupt the power supply. 6 3 Connect the printer to your computer. ' · If you're using a USB cable, plug the square end of the cable into your printer as shown. [. . . ] Since radiation emitted by the laser is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation. CDRH Regulations The Center for Devices and Radiological Health (CDRH) of the U. S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. Compliance is mandatory for products marketed in the United States. The label shown below indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. 20 Laser Safety Labels Warning: Use of controls, adjustments, or performance of procedures other than those specified in this guide may result in hazardous radiation exposure. Your printer is a Class 1 laser product as defined in IEC 825 specifications. The label shown below is attached in countries where required. Internal Laser Radiation Maximum Radiation Power: Wavelength: 0. 73 mW at laser aperture of the print head unit 770 to 810 nm This product employs a Class IIIb Laser Diode. The Laser Diode and Scanning Polygon Mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICE ITEM. The print head unit should not be opened under any circumstance. 21 Ozone Safety Ozone emission Ozone gas is generated by laser printers as a by-product of the printing process. Ozone is produced only when the printer is printing. Ozone exposure limit The recommended exposure limit for ozone is 0. 1 parts per million (ppm) expressed as an average time-weighted concentration over an eight (8) hour period. The EPL-5700i laser printer generates less than 0. 01 ppm for eight hours of continuous printing when considering a closed room of approximately 1000 cubic feet (8' x 10' x 12'). Minimize the risk To minimize the risk of exposure to ozone, you should avoid the following conditions: · Use of multiple laser printers in a confined area (see above) · · · Operation in conditions of extremely low humidity Poor room ventilation Continuous printing for a long period combined with any of the above Printer location The printer should be located so that the exhaust gases and heat generated are: · · Not blown directly into the user's face Vented directly out of the building whenever possible 22 Other Safety Instructions · Be careful not to touch the fuser, which is marked CAUTION Hot Surface Avoid Contact. If the printer has been in use, the fuser can be very hot. CAUTION Hot Surface Avoid Contact · Avoid touching the components inside the printer unless instructed to do so in this guide. Try not to touch the toner and avoid all contact with your eyes. Follow all warnings and instructions marked on the printer. Unplug the printer from the electrical outlet before cleaning. Use a damp cloth for cleaning and do not use liquid or aerosol cleaners. Do not use the printer near water. · · · · 23 · · Do not place the printer on an unstable cart, stand, or table. Slots and openings, located on the sides and bottom of the printer, are provided for ventilation. Keep these slots and openings clear to allow proper ventilation. Avoid placing the printer on a bed, sofa or other soft surface, or in a small enclosed area, as this restricts proper ventilation. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ]