User manual EPSON EXPRESSION 836XL

[. . . ] ® EPSON ExpressionTM 836XL User's Guide Color Image Scanner FCC Compliance Statement for United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Insert the paper stack into the ADF until it meets resistance. If your document is in portrait orientation (top and bottom edges are shorter than the side edges), insert the document bottom edge first. Using Optional Equipment Page 61 If your document is in landscape orientation (top and bottom edges are longer than the side edges), insert the document left edge first. Caution: When scanning high-quality color or halftone documents, it is best to open the ADF and scan documents as described in Loading documents manually. You'll get an option error and possibly a paper feeding error. Always close the ADF before scanning or using the feeder. If your documents are large, pull out the paper support. 3 Slide the edge guides to the edges of your paper. 4 Follow the steps in your software's user's guide to scan your document. Using Optional Equipment Page 62 Loading documents manually You can load documents manually while the ADF is installed. Open the ADF and place the document on the document table. Then close the ADF and scan the document as described in Scanner Basics. Using Optional Equipment Page 63 Fixing Paper Jams in the Auto Document Feeder If a paper jam occurs, first open the ADF's cover to determine where the paper jam occurred. Using Optional Equipment Page 64 If paper jams in the feeder, open the cover on the left and slowly pull out the jammed paper as shown. (Be careful not to pull too hard or the paper may tear, making it more difficult to remove. ) pull paper out this way or this way open cover Using Optional Equipment Page 65 If paper jams in the paper eject position, open the cover on the right and slowly pull out the jammed paper as shown. (Be careful not to pull too hard or the paper may tear, making it more difficult to remove. ) open cover pull paper out this way or this way After removing the jammed paper, close the ADF cover and reset the scanner by turning it off and on again or pressing the RESET button. Using Optional Equipment Page 66 Adjusting the Scanning Position of the Auto Document Feeder If your document feeds into the ADF too far or not far enough, adjust the scanning position using the adjustment dials. This problem may occur if the stopper is not installed or not positioned properly on the document table, so first make sure the stopper is installed as described in Installing the Auto Document Feeder. To access the dials, slide open the dial cover on the rear of the ADF. -6 -5 - -7 -6 -5 - -7 Using Optional Equipment 45 67 45 67 m m 4 -3 -2 -1 0 123 4 -3 -2 -1 0 123 m m Page 67 The right dial controls where paper stops when it is first loaded from the feeder. The left dial controls where double-sided originals stop during scanning of the second side. 4 -5 - -3 -2 4 -5 - -3 -2 -1 0 1 2 3456 -1 0 1 2 3456 mm mm If the upper portion of the scanned image is missing, turn the dial clockwise. The position changes in 1 mm (0. 04 inch) increments. If the lower portion of the scanned image is missing, turn the dial counterclockwise. The position changes in 1 mm (0. 04 inch) increments. Using Optional Equipment 7 -7 6 7 -7 6 Page 68 3 Maintaining and Transporting Your Scanner This chapter gives tips on caring for your scanner and preparing it for a move in these sections: Cleaning the Scanner Replacing the Fluorescent Lamp Transporting the Scanner Page 69 Cleaning the Scanner Caution: Never open the scanner case. To keep your scanner operating at its best, you should clean it periodically. Before cleaning it, unplug the scanner's power cable. Then clean the outside with mild detergent diluted in water. If the glass of the document table gets dirty, clean it with a soft dry, lint-free cloth. If grease or other hard-to-remove material gets on the glass, remove it with a small amount of glass cleaner on a soft lint-free cloth. Wipe off any remaining moisture with a dry lint-free cloth. Do not: Scratch or damage the document table glass Use a hard or abrasive brush to clean it Use alcohol, thinner, or corrosive solvents Spill liquids into the scanner mechanism or electronic components Spray lubricants inside the scanner Maintaining and Transporting Your Scanner Page 70 Replacing the Fluorescent Lamp Caution: Never open the case of the scanner. If you think repairs or adjustments are necessary, consult your Epson Customer Care Center. The luminosity of the fluorescent lamp declines over time. [. . . ] Remove the second frame by clicking on the Delete Marquee tool . Align the left edge of the original frame with position 4 on the scale. Click on the Return to Full Preview button . 5 Troubleshooting Page 93 6 Repeat steps 3 and 4 for the bottom scale. Write down the position of the original frame edge on the bottom scale. 7 Use the procedure in Calculating the Adjustment Angle to calculate the proper adjustment angle. [. . . ]