User manual EPSON EXPRESSION HOME XP-423

[. . . ] If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced radio/TV technician for help. WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels that exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. [. . . ] Also, photo quality and glossy paper are too thick to feed into the ADF successfully. Checks: B5: A4: Letter: Legal: 3 × 5 inches (76 × 127 mm) 7. 17 × 10. 1 inches (182 × 257 mm) 8. 27 × 11. 69 inches (210 × 297 mm) 8. 5 × 11 inches (215. 9 × 279. 4 mm) 8. 5 × 14 inches (215. 9 × 355. 6 mm) Before loading the ADF, make sure the document: Has no wet ink on it. Has no holes and is not ripped or wrinkled. Has no staples or other objects attached that may damage the feeder. Is not printed on photo quality or glossy paper. Has no cut-out areas. Using Optional Equipment Page 46 Follow the steps below to load paper in the ADF: 1 Slide the edge guides all the way out. For checks, move the left edge guide toward the center until it stops, then place your checks in the tray. Move the right edge guide flush against the checks. 2 Arrange your stack of originals face up, with the page you want to scan first on the top. Insert the paper stack into the ADF until it meets resistance. Make sure that the side you want to scan is facing up. Using Optional Equipment Page 47 3 Slide the edge guides to the edges of your paper. When scanning high-quality color or halftone documents, it is best to open the ADF and scan documents as described in Loading documents manually. You'll get an option error and possibly a paper feeding error. 4 Follow the steps in your electronic EPSON TWAIN Pro User's Guide to scan your document. Loading documents manually You can load documents manually while the ADF is installed. 1 Make sure the transportation lock is in the UNLOCK position. 2 Align the SCSI ID rotary switch with the asterisk (*). 3 If you're using a transparency unit or auto document feeder, remove it. Position the two hinges on the cover over the corresponding pins on the scanner, as shown, then push down gently. 5 Turn the scanner on and wait until the carriage moves to the home position (toward the back of the scanner). Then turn the scanner off. Maintaining and Transporting Your Scanner Page 53 6 Slide the transportation lock to the LOCK position. UNL OCK LOC K UNLO CK LOCK OPTIO N TERMINA TOR ON SW SCSI ID 0 7 6 54 1 2 3 OFF Maintaining and Transporting Your Scanner Page 54 Transporting the Transparency Unit After you've removed the transparency unit from the scanner, prepare it for shipping as follows: 1 Slowly raise the front of the transparency unit to allow the lamp assembly to slide to the home position at the back of the unit. Wait until the lamp assembly comes to rest. let the lamp assembly slide to the home position Maintaining and Transporting Your Scanner Page 55 2 Reinstall the unit's shipping screw in the hole marked CLAMP. Maintaining and Transporting Your Scanner Page 56 Troubleshooting This chapter helps you solve scanner problems. It includes the following sections: Diagnosing Problems Upgrading Your System Problems and Solutions Diagnosing Problems Some problems can involve your software or computer, such as: Incorrect setup of the SCSI interface Inappropriate selection of the scanner functions Incorrect setup of your computer or software Incorrect operation of your scanner software If an error occurs, check the scanner's indicator lights. See Indicator Lights to determine what kind of error it is, and try the suggested solutions. If that doesn't solve the problem, see Problems and Solutions. See the documentation that came with your software, computer, and printer for other possible solutions. Troubleshooting Page 57 Indicator Lights If an error occurs, the scanner stops operating. The READY and ERROR lights indicate the type of error. [. . . ] A process in which software or an output device simulates continuous tones with groups of dots. The item, such as a sheet of paper or a book, that is placed on the document table for the scanner to read. The higher the value, the higher the resolution. Images represented with various shades of gray in addition to black and white. [. . . ]