User manual EPSON EXPRESSION PREMIUM XP-620

[. . . ] If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced radio/TV technician for help. WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels that exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. [. . . ] Secure the connection by tightening the connector screws. Using Optional Equipment Page 58 8 Caution: If the ADF misfeeds, first make sure the stopper and paper out support are in place and correctly installed. Peel off the backing from the stopper and from the paper out support provided with the ADF. Then attach the stopper and paper out support to the scanner as shown. Insert the tabs on the paper out support into the slots at the right end of the document table. paper out support stopper 9 Close the ADF. 10 Reattach all the scanner cables and turn on the scanner. Using Optional Equipment Page 59 Loading Paper in the Auto Document Feeder Caution: Do not feed photographic sheets or valuable original artwork into the ADF; misfeeding may result in accidental wrinkling or damage to your original. The ADF can hold up to 30 sheets of the following paper sizes, based on a paper weight of 17 lb and a thickness of 0. 2 inch (6. 0 mm) or less: Paper size Direction A3, Ledger, B4, Legal, A4, Letter, B5, A5, Portrait 5. 5 × 5. 8-inch (140 × 148 mm) A4, Letter, B5, A5 Landscape See Specifications for complete paper requirements. Before loading the ADF, make sure the document: Has no wet ink on it. Has no holes and is not ripped or wrinkled. Has no staples or other objects attached that may damage the feeder. Is not bound. Page 60 Using Optional Equipment Note: You can automatically scan both sides of a document using the ADF-double sided setting in EPSON TWAIN Pro. See the software's online user's guide for instructions. Has no carbon coating. Has no cut-out areas. Follow the steps below to load paper in the ADF: 1 Slide the edge guides all the way out. 2 Arrange your stack of originals face up, with the page you want to scan first on the bottom. Insert the paper stack into the ADF until it meets resistance. If your document is in portrait orientation (top and bottom edges are shorter than the side edges), insert the document bottom edge first. Using Optional Equipment Page 61 If your document is in landscape orientation (top and bottom edges are longer than the side edges), insert the document left edge first. Caution: When scanning high-quality color or halftone documents, it is best to open the ADF and scan documents as described in Loading documents manually. For details, contact your local Epson Customer Care Center (see Where to Get Help for details). Maintaining and Transporting Your Scanner Page 71 Transporting the Scanner Note: If the scanner is inoperable, the carriage may not automatically return to the home position. If it doesn't, raise the right side of the scanner and hold it up until the carriage comes to rest at the left side. Then turn the transportation lock screw to the locked position. If you need to transport the scanner or store it for an extended period, you must secure the carriage beforehand. Turn on the scanner and wait until the carriage moves to the home position (the left side). Turn the transportation lock screw to the locked position to secure the carriage. home position is on this side Maintaining and Transporting Your Scanner Page 72 4 Diagnosing Problems Troubleshooting This chapter helps you solve scanner problems in these sections: Upgrading Your System Problems and Solutions Using the Document Guide Diagnosing Problems Some problems you may have can involve your software or computer, such as: Incorrect setup of the parallel or SCSI interface Inappropriate selection of the scanner functions Incorrect setup of your computer or software Page 73 Incorrect operation of your scanner software If an error occurs, check the scanner's indicator lights. See Indicator Lights to determine what kind of error it is, and try the suggested solutions. If that doesn't solve the problem, see Problems and Solutions. See the documentation that came with your software, computer, and printer for other possible solutions. Troubleshooting Page 74 Indicator Lights If an error occurs, the scanner stops operating. The READY and ERROR lights indicate the type of error. ERROR light On READY light On Error type Solution Command The scanner has received incorrect commands from your error scanning software. If the error still occurs, try restarting the scanner. Interface error The interface setup is wrong or the scanner is not properly connected to the computer. [. . . ] Align the holes on the guide over the pins. arrow adjust pin guide pin clear document guide Troubleshooting Page 88 3 Place the grid document guide onto the guide pins with the oval hole on the right and the round hole on the left. 4 Close the document cover. Troubleshooting Page 89 Scanning the Document Guide 1 Open an application and access EPSON TWAIN Pro. Select the following settings: EPSON TWAIN Pro Settings Document Source: Flatbed Image Type: 256 Grayscale Destination: LineWork Scan Resolution: 800 dpi Click Preview. You see a preview of the document guide in the preview area. (See the EPSON TWAIN Pro User's Guide for details. ) Troubleshooting Page 90 2 Make a marquee around the alignment dots on the document guide. scale boxes marquee Troubleshooting Page 91 3 Use the Marquee tool to create another frame around the top scale. second marquee Troubleshooting Page 92 4 Use the Zoom tool to view the enlarged scale. [. . . ]