User manual EPSON FX-2180

[. . . ] El manual en español comienza aproximadamente a la mitad del libro. El manual en inglés comienza después de esta página. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. [. . . ] 3. Turn on the printer, if necessary. Slide the left edge guide until it locks in place next to the triangle mark on the paper guide. Next adjust the right edge guide to match the width of your paper. 4. Insert a sheet of paper with the printable side down between the edge guides until it meets resistance. The printer feeds the paper automatically and is ready to print. If the first printed line on your page appears too high or low, you can use the Micro Adjust function to adjust the top-of-form position. See page 32 for more information. Paper Handling 27 Loading Special Papers Follow the guidelines in this section when loading single-sheet multipart forms, labels, envelopes, and postcards. Single-sheet multipart forms To load single-sheet multipart forms, use the front paper entry slot with the optional front paper guide or front sheet guide installed. Thick paper, such as multipart forms with five or six parts, requires a straight paper path to avoid paper jams. For more information, see the Reference Guide. Labels When printing on labels, use only the type of labels that are mounted on continuous backing sheets with sprocket holes for use with a tractor feeder. Do not try to print on single sheets with labels because the printer may not feed labels on a shiny backing sheet properly. Thick paper, such as continuous paper with labels, requires a straight or almost straight paper path. You can load labels in the front (to the pull tractor) or bottom (pull tractor) paper slot. The loading procedure for continuous paper with labels is the same as that for ordinary continuous paper, except you must set the paper-thickness lever to 2 before printing. Before printing, turn on the card mode by pressing the Tear Off/Bin button several times until the left Tear Off/Bin light is on. When loading A6 size cards, always load them long edge first. 30 Paper Handling Using the Micro Adjust Function The Micro Adjust function allows you to move the paper forward or backward in 1/216-inch (0. 118 mm) increments to adjust the tear-off and top-of-form positions. Adjusting the tear-off position If your paper's perforation is not aligned with the tear-off edge, you can use the Micro Adjust function to move the perforation to the tear-off position, as described below. Your tear-off position setting remains in effect until you change it, even if you turn off the printer. c Caution: the knob to adjust the tear-off position; this may damage the Never use printer or cause it to lose the tear-off position. You may need to press the Tear Off/Bin button to advance the paper to the tear-off position. Make sure the Tear Off/Bin light is flashing (the paper is at the current tear-off position). Hold down the Pause button for about three seconds. The Pause light begins flashing and the printer enters the Micro Adjust mode. 2. Paper Handling 31 3. Open the paper guide cover, then press the LF/FF D button to feed paper backward, or press the Load/Eject U button to feed paper forward, until the paper perforation is aligned with the tear-off edge of the printer cover. Tear-off edge of the printer cover Paper perforation Note: The printer has a minimum and a maximum tear-off position. If you try to adjust the tear-off position beyond these limits, the printer beeps and stops moving the paper. Press the Pause button to turn off Micro Adjust mode. When you resume printing, the printer automatically feeds the paper back to the top-of-form position and begins printing. Adjusting the top-of-form position The top-of-form position is the position on the page where the printer starts printing. If your printing appears too high or low on the page, you can use the Micro Adjust function to adjust the top-of-form position, as described below. Your top-of-form position setting remains in effect until you change it, even if you turn off the printer. c Caution: the knob to adjust the top-of-form position; this may damage the Never use printer or cause it to lose the top-of-form position. 32 Paper Handling 1. [. . . ] It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. For Canadian users This Class B digital apparatus meets all requirements of the Canadian Interface Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouileur du Canada. EPSON AMERICA, INC. , LIMITED WARRANTY What Is Covered: Epson America, Inc. [. . . ]