User manual EPSON PERFECTION 3200 PHOTO

[. . . ] 7 W in power saving mode Electrical standard Full Speed mode (12 Mbit/s) and High Speed mode (480 Mbit/s), Universal Serial Bus Specification Revision 2. 0 Connector pin arrangement Pin number 1 2 3 4 Signal VCC ­DATA +DATA GND Connector Note: Scanners sold outside the US market may operate at a different voltage. Check the label on the back of the scanner for voltage information. Environmental Temperature Humidity (without condensation) Operating conditions Operation: 41 to 95 °F (5 to 35 °C) Storage: ­13 to 140 °F (­25 to 60 °C) Operation: 10% to 80% Storage: 10% to 85% Ordinary office or home conditions; avoid extreme dust, direct sunlight, and strong light sources. FireWire Interface Interface type Data transfer Synchronization Encoding/ Decoding Logic level: Power class IEEE 1394a-2000 compatible Half-duplex data / strobe differential serial Clock synchronization with DS-Link DS-Link 3. 3. [. . . ] 950 FCC part 15 subpart B class B CSA C108. 8 class B Connector pin arrangement Pin number 1 Signal VCC GND TPB­ TPB+ TPA­ TPA+ Connector USB Interface Interface type Connector type Configuration Universal Serial Bus Specification Revision 2. 0 One receptacle (Type B) 2 3 4 5 6 2 1 4 3 6 5 Transparency Unit Element Characteristics Description Self-powered Remote wake up feature: Not supported Maximum power consumption from VBUS: 2mA (5V) Interface Endpoint 1 No alternate setting Class: Vendor specific Bulk IN transfer Maximum data transfer size: 64 bytes (Full Speed) 512 bytes (High Speed) Endpoint 2 Bulk OUT transfer Maximum data transfer size: 64 bytes (Full Speed) 512 bytes (High Speed) String Descriptor Language ID: US English 1: Manufacturer: "EPSON" 2: Product: "EPSON Scanner" The transparency unit is built into the scanner lid. Electrical Document specifications Supply voltage: DC 24 V ±10% V Rated current: 0. 5 A Positive or negative film in the following sizes: 35 mm strips 35 mm slides 120/220 (6 × 9-cm) film 4 × 5-inch film 4 × 9 inches (102 × 230 mm) Readable area 2 - EPSON Perfection 2450 PHOTO 9/01 EPSON Perfection 2450 PHOTO Using Film Holders Film has two sides, a shiny base side and a dull emulsion side. The base side of the film has the film maker's name and film ID numbers printed on it. To scan 35-mm film strips, 4 × 5-inch film, or 120/220 (6 × 9cm) film, place the film in the correct holder, as shown: Scanning Transparencies and Film Before scanning transparent documents, you need to remove the scanner's reflective document mat; this exposes the scanner's transparency unit (light source), which is built into the lid. If you're scanning slides or film strips, you'll also need to use one of the film holders. Using the Transparency Unit To use the transparency unit, remove the reflective document mat by grasping the top of the mat and sliding it up gently, as shown. 120/220 (6 × 9-cm) film 35-mm strips remove mat by sliding it up transparency unit 4 × 5-inch film Place the holder with the film onto the scanner. Make sure the white triangle on the holder points to the upper-right corner of the scanner. Make sure the cable for the tranparency unit is plugged into the round connector. Follow the on-screen steps for each option. 4 - EPSON Perfection 2450 PHOTO 9/01 EPSON Perfection 2450 PHOTO Selecting TWAIN Settings If you need to manually adjust the settings in EPSON TWAIN, follow the guidelines shown at right. The illustration shows the preferred order in which settings should be adjusted. Detailed descriptions are given in the electronic Reference Guide. The most important thing to remember when scanning is to select the correct image type and resolution for your scan. 2 Preview your image 1 Select basic settings: Document Source Image Type Destination Resolution 3 Automatically set the scan area for your image using Auto Locate 4 Size or scale the image 5 Customize your exposure and use color management 6 Scan the image into your application 7 Close EPSON TWAIN Indicator Light The indicator light (next to the ] Start button) indicates the status of the scanner, as described below. Light On Flashing Flashing Color Green Green Red Status The scanner is ready to scan images. The scanner is initializing (warming up) or is busy scanning. Check the following, then turn your scanner off and back on to reset it: Make sure the transportation lock is turned to the unlocked position. [. . . ] Check the following, then turn your scanner off and back on to reset it: Make sure the transportation lock is turned to the unlocked position. Make sure the scanner is properly connected to your computer. [. . . ]