User manual EPSON PL-7000

[. . . ] User's Guide All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein. [. . . ] Adjusts the difference between light and dark areas. Increase the contrast to make light areas lighter and dark areas darker. Decrease it to minimize the difference between light and dark areas. Synchronizes with the tracking signal sent from the computer. Adjust this setting to correct fuzziness or to remove streaks from the image. Matches the projector's internal clock to various computer graphic signals. Adjust this setting to remove fuzzy lines from the image. Adjusts the color balance of the input source. Select this item and then press the Enter button (control panel) or either multi-purpose button (remote) to enter the color adjustment mode. Then use the pointer button or up and down buttons (control panel) to select a color. Next, use the pointer button or left and right buttons (control panel) to adjust the selected color. Increase the color setting for more intense color on the screen, and lower the setting for less intense color. When you finish making adjustments, press the Enter button (control panel) or a multi-purpose button (remote) to return to the Computer menu. Contrast Sync Tracking Color ssssss 48 3 · Using the Projector Menus Menu item Position Description Select this item and then press the Enter button (control panel) or either multi-purpose button (remote) to enter the screen position adjustment mode. Then use the pointer button or up, down, left, and right buttons (control panel) to move the screen position in the corresponding direction. When you finish making adjustments, press the Enter button (control panel) or a multi-purpose button (remote) to return to the Computer menu. Mouse/Com Locks and unlocks the Mouse/Com port. Select 1 to assign the wireless mouse control to the computer connected to the Mouse/Com 1 port. The wireless mouse controls the computer connected to Mouse/Com 1 only if the input source is switched to Computer 2. Select 2 to assign the wireless mouse control to the computer connected to the Mouse/Com 2 port. Selecting 1 2 tells the projector to automatically switch wireless mouse control whenever the input source computer is changed. Reset Returns all Computer menu items to their initial factory defaults. Select this item and then press the Enter button (control panel) or either multi-purpose button (remote) to display the confirmation screen. Next, select Yes and then press the Enter button (control panel) or a multi-purpose button (remote) to reset the Computer menu. If you change your mind, select No and then press a multi-purpose button (remote) or the Enter button to clear the confirmation screen without changing any settings. Return Saves changes and displays the Main menu. sssssss Menu Options 49 Video Menu (Image source = Video) The Video menu enables you make adjustments to the projected image. [. . . ] To display a higher resolution image, the projector compresses it to 1024 × 768. The following table lists the display formats supported by the projector: Computer type IBM PC and IBM PC compatible Formats VGA, VESA, JEGA CGA, SVGA, XGA Resolutions 640 × 480 640 × 200 640 × 400 800 × 600 1024 × 768 1280 × 1024* 640 × 480 832 × 624 1024 × 768 1017 × 768 1152 × 870* 640 × 480 800 × 600 1024 × 768 Apple Macintosh Standard 8- and 24-bit color monitor NEC PC * The projector uses a patent-pending technology to resize the image to 1024 × 768. Note: The frequencies of some computers may not allow the image to be displayed correctly. Note: This projector is compatible with DDC-capable graphic sub-systems and boards only. sssssss 95 Monitor and Computer In 1/2 connector pin assignments The Monitor and Computer In 1/2 connectors are female video RGB, 15-pin micro-D-style connectors. The pin assignments are: Input pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Monitor connector signals Red out / red video Green out / green video Blue out / blue video Reserved GND GND GND GND Reserved GND Reserved Reserved Horizontal sync Vertical sync Vertical sync Computer In 1/2 connector signals Red video Green video Blue video Monitor (ID bit 2) GND Red video GND Green video GND Blue video GND +5 V Synchronous GND Monitor (ID bit 0) SDA Horizontal sync Vertical sync Reserved ssssss 96 7 · Technical Specifications s s s s s s s s s s s s s s Glossary Brightness. [. . . ]