User manual EPSON POWERLITE 713C

[. . . ] EPSON PowerLite 503c/713c Multimedia Projector ® ® User' Guide s Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. [. . . ] You see a message like the one at the right. Use the Enter button on the remote control to select a zoom rate (display size), and then press Enter. When you see the message "Do you save the user logo?, " select Yes and press Enter. Do not use the projector or other sources (computer, video, speaker, etc. ) while the logo is being saved. When you see the message "Saving the user logo is completed, " press Esc or Menu. Selecting When the Image Displays After your image is saved, you can set it up as the no-signal message and/or the screen that's displayed when you press the A/V Mute button. Press the Menu button to display the main menu (if not already displayed). Use the Enter button to highlight Setting. Use the Enter button to highlight No-Signal Msg. This sets your image as the screen displayed when the projector is not receiving a signal. If you want to set up your image as the A/V Mute display, use the Enter button to move down to A/V Mute. This sets your image as the screen displayed when you press the A/V Mute button. When you're finished, press Esc or Menu. note You can also set up your image as a startup screen. Use the Advanced menu to enable the startup screen; see page 48. Fine-tuning the Projector 45 To test your setting, press the A/V Mute button to display your image. Press it again to turn off the image. Customizing Projector Features You can use the Setting menu to enable the projector's power management system, adjust the image shape, and customize several other features. Use the Enter button to highlight Setting. You see the features and their settings on the right side: 3. Use the Enter button to set the following options: I Keystone Adjusts a distorted image from a trapezoid shape to rectangular. I P in P Changes from a composite (standard) video source to an S-video source for the picture-in-picture display. 46 Fine-tuning the Projector I No-Signal Msg. Selects the screen color and message to display when the projector is not receiving a signal. The logo setting displays an image that you have transferred to the projector. See page 44 for instructions on transferring an image to use as the no-signal message. I Prompt Turns off the identifying text that appears briefly when you switch from computer input to a video source. I A/V Mute Selects the screen color or image to display when you press the A/V Mute button. The logo setting displays an image that you have transferred to the projector. See page 44 for instructions on transferring an image to use for the A/V Mute display. I Power Mgmt Sys Enables or disables the power management system, which turns the lamp off when the projector has not received any input signals for 30 minutes. When you're finished, press Esc or Menu. Fine-tuning the Projector 47 Setting Advanced Features You can use the Advanced menu to configure the projector for rear projection or ceiling mounting, and adjust several other features. [. . . ] This warranty does not cover consumables (e. g. , fuses), other than lamps. EPSON is not responsible for warranty service should the EPSON label or logo or the rating label or serial number be removed or should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-EPSON products, or service other than by an EPSON Authorized Servicer. Postage, insurance, or shipping costs incurred in presenting your EPSON product for carry-in warranty service are your responsibility. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred. [. . . ]