User manual EPSON POWERLITE S5

[. . . ] PowerLite S5 Series/77c Multimedia Projector ® User's Guide Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. [. . . ] Aspect Sets the image's aspect ratio (ratio of width to height) to 4:3 for computer or letterbox video content and to 16:9 for widescreen video content. You can also select 16:9 (Up) for a widescreen display at the top of the screen or 16:9 (Down) for a widescreen display at the bottom of the screen. When you're finished adjusting the signal settings, press Esc or Menu. 60 Fine-tuning the Projector Customizing Projector Features The Settings menu lets you customize the way you use the projector, from adjusting lamp brightness and speaker volume to applying security controls. Select the Settings menu. PowerLite S5 Series PowerLite 77c Fine-tuning the Projector 61 3. Then use the up and down arrow buttons and the Enter button to set the following options: Keystone Adjusts a distorted image from a trapezoid shape to rectangular. Auto Keystone (PowerLite 77c only) Automatically adjusts a distorted image from a trapezoid shape to rectangular when the projector's foot is extended or retracted. (Not available when you're projecting from the ceiling or using rear projection. ) Select ON or OFF. Zoom (PowerLite S5 Series only) Adjusts the image size from Wide (larger) to Tele (smaller). Operation Lock note To cancel the Operation Lock function from the projector, press the Enter button for about seven seconds. When turned on, this function disables all projector buttons, or all buttons except the P Power button. Changes to this setting take effect after you restart the projector. (After you turn off the projector, wait for the Ppower light to turn a steady orange before turning it on again. ) See page 71 for more information. Brightness Control Select Low lamp brightness when the projection is too bright for the room. The Low setting also reduces electricity consumption and fan noise. Select High to project the maximum brightness. (Also check the Brightness setting in the Image menu; see page 56. ) Volume Adjusts the volume for the projector's speaker. When you're finished, press Esc or Menu. 62 Fine-tuning the Projector Selecting Projector Setup Options Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen. You see the features and their settings on the right side: 3. Then use the up and down arrow buttons and the Enter button to set the following options: Display Message: Lets you turn screen messages on or off. Display Background: Sets the screen background to Black, Blue, or Logo when no signal is available. Startup Screen: Enables or disables display of the startup note Logo settings cannot be changed if the User's Logo Protect feature has been turned on. See page 68. screen when the projector is turned on. A/V Mute: Sets the screen background to Black, Blue, or Logo when the A/V Mute button is pressed. User's Logo Turn on to display the image or logo you have captured whenever the projector is turned on. See page 67 for more information. Fine-tuning the Projector 63 Projection Front: Projector is in front of the screen. Front/Ceiling: Projector is in front of the screen, mounted upside-down from the ceiling. Rear: Projector is behind the screen. Rear/Ceiling: Projector is behind the screen, mounted upside-down from the ceiling. To change from Front to Front/Ceiling or Rear to Rear/Ceiling, press and hold the A/V Mute button on the remote control for five seconds. Operation Direct Power: When this feature is enabled, projection starts as soon as you plug in the power cord. [. . . ] Do not put in the trash. 102 Notices If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or coming in contact with the eyes or mouth. If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes when you open the lamp cover. WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. (Provided in accordance with Proposition 65 in Cal. Health & Safety Code §25249. 5 et seq. ) Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. [. . . ]