User manual EPSON SPECTROPROOFER MOUNTER 17 INCH

[. . . ] User's Guide NPD4282-00 EN SpectroProofer Mounter 17" User's Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S. ) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. [. . . ] U See "Starting SpectroProofer Utilities" on page 11 Click Printer Linearization. Measuring Color This section introduces the color measuring procedures using SpectroProofer Utilities which is the operation tool for this product. See the online help of the SpectroProofer Utilities for detailed information. Starting SpectroProofer Utilities Follow the instructions below to start SpectroProofer Utilities. Note: You can start SpectroProofer Utilities from printer driver's utility screen (Windows) or from EPSON Printer Utility 4 (Mac OS). 11 SpectroProofer Mounter 17" User's Guide How To Use D Follow the on-screen instructions to perform color calibration. C Click Preparing and executing a color measurement job. D Click the Help button to see the online help for detailed information. Select the job you want to perform. Preparing and executing a color measurement job This section introduces the color measuring procedures using Preparing and executing a color measurement job. See the online help for detailed information. Follow the on-screen instructions to complete the settings. Click the Help button to see the online help for detailed information. Note: The ICC profile cannot be created by the SpectroProofer Utilities alone. You need commercially available profile creation software separately. A B Turn on the printer, and then load the paper. See the printer manual when loading the paper. U See "Supported Media" on page 9 Start the SpectroProofer Utilities. U See "Starting SpectroProofer Utilities" on page 11 12 SpectroProofer Mounter 17" User's Guide Maintenance Maintenance To keep the product in good working condition, we recommend cleaning the parts. B Unplug the two interface cables connected with ILS20EP/ILS20EPUV. Cleaning procedures Cleaning the ILS20EP/ ILS20EPUV A Turn off the printer, and then open the front cover of the mounter. C Hold the front of ILS20EP/ILS20EPUV and lift the rear a little, and then remove it. c Caution: or knock it against hard objects. Do not drop The lens may be scratched or ILS20EP/ ILS20EPUV may be damaged. 13 SpectroProofer Mounter 17" User's Guide Maintenance D Use air to blow any dust and dirt off the lens in ILS20EP/ILS20EPUV. B Remove the mounter. w Warning: flammable gas spray inside or Do not use around this product. C Turn the mounter around, and then remove the backing or the white calibration tile holder. c Caution: the lens directly in ILS20EP/ Do not touch ILS20EPUV. E Install ILS20EP/ILS20EPUV in the mounter, and then close the front cover of the mounter. U See the SpectroProofer Mounter 17" Setup Guide Cleaning the surface of the backing/white calibration tile c Caution:the backing is fragile, do not drop or Because knock it against hard objects. A Open the side cover, and then unplug the printer connection cable. 14 SpectroProofer Mounter 17" User's Guide Maintenance D Remove the white calibration tile from the white calibration tile holder. Cleaning the paper presser A Turn off the printer, and then open the front cover of the mounter. E Use a soft, dry cloth to carefully remove any dust or dirt from the surface of the white calibration tile or the surface of the backing. If the dirt does not come off, soak a soft cloth in water and wring it dry, and then rub away any dirt from the surface. Then, wipe the surface again with a soft, dry cloth. B F See the SpectroProofer Mounter 17" Setup Guide to setup the mounter. U See the SpectroProofer Mounter 17" Setup Guide Hold both ends of the paper presser and lower it forward. C Soak a soft cloth in water with a small amount of mild detergent, wring it dry, and then wipe away dirt from the base (the surface that touches the paper) of the paper presser. Then, wipe it with a soft, dry cloth. 15 SpectroProofer Mounter 17" User's Guide Maintenance C Remove the paper guide unit, and then wipe away the powdery paper. D D Close the front cover of the mounter. Replace the paper guide unit, install the mounter, and then connect the printer connection cable. U See the SpectroProofer Mounter 17" Setup Guide Cleaning the paper guide unit Some powdery paper accumulates in the paper guide unit when the printer cuts paper using the auto cutter. Use the following procedure to periodically clean up the powdery paper (about once a month). A Open the side cover, and then unplug the printer connection cable. B Remove the mounter. 16 SpectroProofer Mounter 17" User's Guide Troubleshooting Troubleshooting When Error Message Appears When an error occurs in the printer (or when the printer enters an abnormal status), the large alert light on the printer and a light on the control panel are lit, and a message is displayed on the LCD panel. When the error message appears, check the following solutions and do the required action. Error message SpectroProofer Error Refer to the manual to find out how to solve the problem. XX (where XX indicates the error number) What to do Check the error number, and then take the following action. For error number 01 Turn off the printer, and then remove the mounter. Install the mounter correctly, and then turn the printer back on. U See "Maintenance" on page 13 U See the SpectroProofer Mounter 17" Setup Guide If the error continues to occur, contact customer support services for assistance. [. . . ] The dealer should always be the first call for advise on problems; they can often solve problems quickly and easily as well as give advise on the next step to take. Speak to a Support Representative Dial: (562) 276-1300 (U. S. ), or (905) 709-9475 (Canada), 6 am to 6 pm, Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. Before you call Epson for support, please have the following information ready: Product name Product serial number Proof of purchase (such as a store receipt) and date of purchase Computer configuration Description of the problem Note: For help using any other software on your system, see the documentation for that software for technical support information. Internet URL http://www. epson. com. au Access the Epson Australia World Wide Web pages. [. . . ]