User manual EPSON STYLUS T10 START HERE

[. . . ] Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. Seiko Epson Corporation shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as Epson Approved Products by Seiko Epson Corporation. EPSON® is a registered trademark, and Epson StylusTM and Exceed Your Vision are trademarks of Seiko Epson Corporation. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. [. . . ] See "Nozzle check" on page 76 See "Head cleaning" on page 78 See "Power cleaning" on page 80 You need to perform head cleaning a few times before the nozzle check pattern is correctly printed. If the nozzles are still clogged after performing head cleaning three times, perform power cleaning. See "Head cleaning" on page 78 See "Power cleaning" on page 80 After performing the head cleaning a few times, turn off the printer and leave it overnight or longer, so that the ink may dissolve. If the nozzles are still clogged after trying the instructions above, contact your Epson dealer. Transporting the Printer When transporting the printer, repack the printer using the original box and packing materials to protect from shock and vibration. c Caution: remove the ink cartridges; Do not otherwise, the print head nozzles may dry up or ink may leak from the cartridge. Be careful not to touch the parts unless you needed to; otherwise, the printer may be damaged. Repacking the printer A B C D E Turn off the printer, and then unplug the cables such as the power cord. Remove the roll paper and roll media adapter if they are set in the printer. Remove the paper basket if it is installed. Remove the optional Auto Take-up Reel Unit or SpectroProofer Mounter if they are installed. Open the front cover to install the protective material for fixing the print head, and then close the cover. See the Unpacking and Setup Guide Protecting the print head This printer has a capping function that automatically puts a cap on the print head to keep it away from drying. If the print head is left uncapped, the print quality may decline. When you are not using the printer, make sure the print head is located on the far right so that it is capped. Paper is not cut correctly. Check the Source setting in the printer driver and printer's control panel, and load the paper correctly. Press the button to release the paper presser, and open the front cover. See "Feeding or ejecting troubles" on page 107 Paper cutter may be dull. See "Replacing the Cutter" on page 72 89 Epson Stylus Pro 7900/7910/9900/9910 User's Guide Problem Solver Error messages CUTTER UNIT NEARING END OF SERVICE LIFE. RECOMMEND REPLACING THE CUTTER UNIT PAPER ERROR LOAD PAPER CORRECTLY REFER TO THE MANUAL Description Paper cutter may be dull. The paper is not loaded correctly. What to do Replace the paper cutter. See "Replacing the Cutter" on page 72 Press the button to release the paper presser, and remove the paper. See "Using Roll Paper" on page 31 See "Using Cut Sheet Media" on page 38 PAPER SENSOR ERROR PRESS THE BUTTON LOAD DIFFERENT PAPER The barcode has not been read correctly. Press the button to clear the error, or press the button to release the paper presser to set a different paper. See "Using Roll Paper" on page 31 See "Using Cut Sheet Media" on page 38 PAPER LOW The roll paper is close to running out. The paper installed is not supported for borderless printing. Replace the roll paper with a new one. See "Using Roll Paper" on page 31 Press the button to cancel jobs, and then eject the paper. See "Using Roll Paper" on page 31 See "Using Cut Sheet Media" on page 38 See "Paper Information" on page 171 BORDERLESS ERROR LOAD A SUPPORTED PAPER SIZE OR LOAD PAPER CORRECTLY The size of the cut sheet media is not recognized properly. If the paper is wavy or slack, the printer cannot recognize the paper size correctly. [. . . ] Arteri Mangga Dua, Jakarta Phone/Fax: (62) 21-62301104 Lippo Center 8th floor Jl. Gatot Subroto No. 2 Bandung Phone/Fax: (62) 22-7303766 Hitech Mall lt IIB No. Kusuma Bangsa 116 ­ 118 Surabaya Phone: (62) 31-5355035 Fax: (62)31-5477837 Hotel Natour Garuda Jl. 60 Yogyakarta Phone: (62) 274-565478 Wisma HSBC 4th floor Jl. [. . . ]