User manual EPSON WORKFORCE DS-6500N

[. . . ] Accidental disruption of power can erase valuable information in your computer’s and printer’s memory.  Make sure that there is no dust on the socket.  Be sure to insert the plug completely into the electrical outlet.  Do not handle the plug with wet hands. [. . . ] Safety Instructions 4 AL-MX200 Series Safety Information Guide ❏ Do not put your printer where the cord will be stepped on. ❏ Do not use printer in a damp environment.  Avoid locations that are subject to direct sunlight, excessive heat, moisture, oil vapor, or dust.  Do not place the printer on an unstable surface.  Slots and openings in the cabinet and the back or bottom are provided for ventilation. Do not put the printer on a bed, sofa, rug, or other similar surface or in a built-in installation unless proper ventilation is provided.  Keep the entire computer and printer system away from potential sources of interference, such as loudspeakers or the base units of cordless telephones.  Leave adequate room around the printer to allow for sufficient ventilation. Using the printer ❏ Be careful not to touch the fusing unit, which is marked CAUTION, or the surrounding areas. If the printer has been in use, the fusing unit and the surrounding areas may be very hot. If you must touch one of these areas, turn off the printer and wait 40 minutes to allow the heat to subside before doing so.  Unplug this printer from the wall outlet before cleaning.  Use a well-wrung cloth for cleaning and do not use liquid or aerosol cleaners. Handling consumable products ❏ Do not burn used consumable products because they might explode and injure someone. dispose of them according to local regulations. Safety Instructions 6 AL-MX200 Series Safety Information Guide ❏ Be sure to keep consumable products out of the reach of children.  When handling a toner cartridge, always place it on a clean, smooth surface.  Do not attempt to modify a toner cartridge or take it apart. If toner gets on your skin or clothes, wash it off with soap and water immediately.  If toner is spilled, use a broom and dustpan or a damp cloth with soap and water to clean it up. Because the fine particles can cause a fire or explosion if they come into contact with a spark, do not use a vacuum cleaner.  Wait at least one hour before using a toner cartridge after moving it from a cool to a warm environment to prevent damage from condensation. [. . . ] Udsættes den for lys, kan det beskadige tromlen, forårsage mørke og lyse områder på den udskrevne side og reducere levetiden for tromlen.  Vent mindst en time, før du bruger en tonerkassette, hvis den forinden er flyttet fra kolde til varme omgivelser, for at undgå skader på grund af kondensering. Reducering af risikoen Du bør undgå følgende situationer for at minimere risikoen for eksponering med ozon: ❏ Brug af flere LED-printere på begrænset plads ❏ Brug i omgivelser med ekstrem lav fugtighed ❏ Dårlig udluftning af rum ❏ Langvarig, kontinuerlig udskrivning sammen med en af ovennævnte Placering af printer Printeren bør placeres, så de afgivne gasser og varme: ❏ Ikke blæses direkte ind i brugerens ansigt ❏ Sendes direkte ud af bygningen, hvor dette er muligt Standarder og godkendelser Europæisk model AL-MX200DNF Lavspændingsdirektiv 2006/95/EC EMC-direktiv 2004/108/EC EN60950-1 EN55022 Klasse B EN61000-3-2 EN61000-3-3 EN55024 ✓ ✓ ✓ ✓ ✓ AL-MX200DWF ✓ ✓ ✓ ✓ ✓ Sikkerhedsinstruktioner 7 AL-MX200 Series Safety Information Guide R&TTE-direktiv 1999/5/EC EN300 328 EN301 489-1 EN301 489-17 ETSI ES203 021 EN60950-1 ✓ ✓ ✓ ✓ ✓ ✓ ✓ Europæiske brugere (kun AL-MX200DNF) Vi, Seiko Epson Corporation, erklærer hermed at dette apparat, model L722A, er i overensstemmelse med de essentielle krav og andre relevante bestemmelser i direktivet 1999/5/EC. Epson kan ikke acceptere ansvar for nogen former for manglende opfyldelse af beskyttelseskravene, der medfører en ikke-anbefalet modificering af produkterne. [. . . ]