User manual ESCALADE SPORTS 2L-6193-02

[. . . ] B9914-1 B9940-1 B9941-1 READ THESE INSTRUCTIONS CAREFULLY TOLL FREE 1-800-426-1421 (THIS IS A CONSUMER ONLY NUMBER) Please have this Owner's Manual with you when you call. Or write us at: CUSTOMER SERVICE DEPT. , P. O. Box 889 Evansville, IN 47706 Fax Number: (812) 467-1399. Please provide model number and/or part number (not just the key number) of the product and/or part when you call or write. [. . . ] However, if mounting to a Universal Mounting Bracket (like the one shown) or similar mounting system where the goal is only supported by the backboard, you must use the Temporary Safety Strap shipped with this backboard. Without extra support behind the goal such as provided by an extension arm pole (see above, left), hanging from the rim and slam dunking the ball may cause the backboard to break. EXTENSION ARM POLE BEFORE MOUNTING THE BACKBOARD: If using a universal mounting bracket, note that you will need to use the Temporary Safety Strap shown at the right. It should be placed between the top left-hand goal mounting hole in the backboard and the bottom left hand backboard mounting hole in the backboard (See right). Follow steps 1-2 below to secure backboard (and safety strap) to your mounting structure. TOOLS NEEDED: Two ½" Wrenches, Pliers, Slotted Screwdriver P/N 2L-6193-02 PRODUCT PARTS LIST FOR MODEL Nos. B9914-1, B9940-1, B9941-1 ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NOS. 900-133V 904-101 900-122B 910-103B 3F-6001-00 2B-6024-00 2B-6025-00 2B-6023-00 1B-6047-00 901-157 1B-6045-00 See Model No. 1B-6046-01 2S-6049-00 1B-6208-00 2B-6089-00 2L-6193-02 DESCRIPTION Goal Assembly Plastic Cover Backplate Assembly Leaf Spring Net 5/16 Std. Washer 5/16-18 Hex Nut 5/16 SplLockwasher 5/16-18 x 3 Hex Bolt 5/16-18 Flange Nut 5/16-18 x 2½ Carr. Safety Strap 5/16" x 1-1/2" Yellow Hex Blt 5/16" Jam Nut, Yellow This Owner's Manual QTY. 1 1 1 1 1 12 8 8 4 1 2 1 2 1 1 1 1 We also recommend ordering a Safety Bracket free of charge to permanently secure the goal to your mounting structure. This safety bracket is not required when using an extension arm pole. Box 889 Evansville, Indiana 47706-9989 1. Attach TOP HALF of backboard to your mounting structure with two bolts #11, two washers #6, two split lockwashers #8, and two hex nuts #7. Locate the yellow bolt (#15) and yellow jam nut (#16) in hardware bags. Assemble nut and bolt to backplate (#3) as shown in Detail A. Tighten securely by threading nut and bolt against one another. Attach TOP HALF of backplate #3 and plastic cover #2 to your backboard with two bolts #9, four washers #6, two split lockwashers #8, and two hex nuts #7. NOTE: If mounting backboard to a universal mounting bracket (or other four hole mount), secure the temporary safety strap to goal at this time. [. . . ] NOTE: There are two different ways this goal can be used: 1) as a spring goal 2) as a conventional goal For spring loaded goal: Screw flange nut onto hex bolt (#15) only until the end of the stud extends through the flange nut. (See FIGURE 4) For conventional goal: Screw flange nut completely onto hex bolt (#15). Attach long loops of net to hooks on bottom of rim. [. . . ]