User manual ESCALADE SPORTS 2L-6516-01

[. . . ] This warranty is also void if product is in any way abused, damaged, or modified from its original state. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 2L-6516-01 TOOLS NEEDED FOR ASSEMBLY CAUTION AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THIS ASSEMBLY !DO NOT LEAVE TABLE UNATTENDED UNTIL ASSEMBLY IS COMPLETE! Rachet (optional) 7/16 Socket (If using rachet) 9/16 Socket (If using rachet) Tools Needed: 7/16 Open or Boxed End Wrenches (2) 9/16 Open or Boxed End Wrenches (2) Pliers Hammer CASTER BEAM ASSEMBLY 5 6 1 5 6 2 FIGURE 1 1. Attach one non - locking caster #3 and one locking caster #2 to each caster rail #1 using one washer #6 and one jam nut #5, as shown in figure 1. [. . . ] (See figure 5) Using a pair of pliers hook spring #13 into hole in safety latch #14. Attach other safety latch to other frame assembly the same way using step 7 and 8. FIGURE 5 Attach hook end of #13 spring into this hole. 9 14 9 27 21 Attach safety latch using this hole. 19 13 12 4 8 18 3 ATTACHING LINKAGE AND LEG ASSEMBLY 10. Place leg end caps #24 in the ends of legs #11. Attach linkages #20 to the outside of the upright #21 using bolt #18, spacer #12, and locknut #9. (See figure 6) Do not over tighten these locknuts, joints must be free to pivot. IMPORTANT: Turn leg assembly #11 as shown in figure 6 and attach other end of linkages #20 to the outside of the leg assembly #11 using bolt #18, spacer #19, and locknut #9. (See figure 6) Do not over tighten these locknuts, joints must be free to pivot. CAUTION Leg assembly # 11 must be attached as shown with cross bar toward inside of table. 18 19 FIGURE 6 20 18 9 9 12 21 9 11 19 9 20 12 24 18 18 4 CAUTION AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THIS ASSEMBLY. DO NOT FOLD TABLE HALVES UP IN THE STORAGE POSITION UNTIL TABLE HALF IS COMPLETELY ASSEMBLED AND ALL OPERATING INSTRUCTIONS ARE UNDERSTOOD. READ AND UNDERSTAND THIS STEP BEFORE ATTACHING TABLE TOPS!AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THIS STEP!Find four bolts #8, spacers #19, and locknuts #9. Place one of each next to caster and leg assembly, so they are handy for this step. With one adult on each side of either table top #23, place table half on frame assembly. (See figure 7) While at least one adult holds up table top half, align holes in upright #21 with top center hole (See detail A) in leg mounting bracket #22. (See figure 7) Secure table top half to upright #21 using bolts #8, spacer #19 between upright #21 and leg mounting bracket #22, and locknut #9. (See figure 7) Secure table top half to leg assembly #11 using bolts #8, spacer #12 between leg assembly #11 and leg mounting bracket #22, and locknut #9. Tighten nuts securely, but do not overtighten, these joints must be free to pivot. Attach other table top half using step 12. DO NOT SCOOT TABLE ACROSS FRAME. FIGURE 7 5 ATTACHING NET AND POST ASSEMBLY FIGURE 8 Net B Net Retaining Hook C Top Plug G Tension Rope D Clamp Screw F Post Assembly A Net Height Adjustment Knob Tension Chain E 14. Place table halves together in playing position. Place post assembly A over the gap between the two table halves. Put long end of net hook C in the end of net B. [. . . ] By following these simple maintenance steps you will add to the life of your new table. 1 2 3 4 5 6 8 9 10 11 12 13 14 15 8S-6201-01 2Q-6086-00 2Q-6085-00 2S-6144-01 701-49 701-50 701-82 701-26 704-140 1A-6132-01 7B-6161-00 5V-6010-00 1A-6137-01 701-105 ReReplacement Parts List for Replacement Parts List For T8261 CASTER RAIL CASTER WITH BRAKE CASTER WITHOUT BRAKE MOUNTING PLATE 3/8 JAM NUT 3/8 WASHER 1/4-20 X 2 HEX HEAD BOLT 1/4-20 LOCKNUT TUBE PLUG LEG ASSEMBLY SPACER SAFETY LATCH SPRING SAFETY LATCH #8 X 9/16 SCREW 4 4 4 8 8 8 14 34 8 2 10 2 2 108 16 17 18 19 20 21 22 23 24 25 26 27 28 2S-6142-05 2S-6143-04 701-35 701-104 8S-6200-01 1A-6133-01 2S-6139-00 705-165W 704-138 2M-6047-00 2L-6516-01 801-9B 5A-6166-00 SIDE RAIL END RAIL 1/4-20 X 2 1/4 HEX HEAD BOLT SPACER LINKAGES UPRIGHT ASSEMBLY LEG MNTG BRACKET TABLE TOP LEG CAP END PROTECTOR INSTRUCTION MANUAL 1/4 WASHER NET AND BRACKET KIT 4 2 20 12 4 2 8 2 4 4 1 2 1 Storage for your table. This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack, or blister. When your table is not in use, it should be folded up in a dry area. [. . . ]