User manual ESCALADE SPORTS 2L-6714-01B

[. . . ] UNLEVEL FLOORS If table does not seem level, it is probably because floor is not level. Move table several inches (set table in playing position) in different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer legs. Manufactured under one or more of the following patents: 6, 345, 820 5, 318, 489 D442, 654 6, 196, 953 5, 271, 625 D425, 943 6, 179, 733 5, 213, 554 D425, 572 6, 120, 397 5, 169, 360 D420, 563 6, 117, 051 5, 158, 512 D330, 234 5, 921, 227 5, 119, 741 D330, 057 5, 919, 102 5, 071, 120 5, 901, 692 5, 067, 728 5, 899, 824 4, 911, 085 5, 816, 957 4, 798, 381 5, 769, 744 4, 717, 157 5, 749, 351 4, 596, 228 5, 718, 212 4, 546, 754 5, 672, 144 4, 519, 374 5, 498, 004 4, 515, 142 5, 392, 757 4, 424, 968 © 2002 Escalade Sports 2L-6714-01B CARE AND MAINTENANCE You have purchased a quality product that will give you years of enjoyment. [. . . ] This warranty is not transferable and does not cover normal wear and tear, bowing of the table or damage caused by improper handling, installation or use of this product. This warranty is also void if product is in any way abused, damaged, or modified from its original state, or if used for other than residential use. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 2 READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2) ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER! 1. Attach wood bottom board (#2) to caster rails (#1) as shown in Figure 1. Turn caster rail as shown with pivot tubes toward inside, and attach tube (#2) with four carriage bolts (#3) and four wing nuts (#4). Tighten wing nuts securely. Figure 1 PIVOT TUBES MUST FACE INWARD AND POINT STRAIGHT UP AS SHOWN! Figure 2 AT LEAST TWO (2) ADULTS ARE NEEDED TO COMPLETE THE REST OF THIS ASSEMBLY!WHEN ASSEMBLING TOPS TO BASE, HANDLE TOP ASSEMBLIES BY GRASPING ONLY THE TOPS THEMSELVES. DO NOT GRASP METAL LEGS, USUPPORT, LINKAGE, OR HINGES. THESE PARTS CAN MOVE AND COULD PINCH FINGERS OR HANDS CAUSING SERIOUS INJURY!ASSEMBLE AS SHOWN WITH LEGS FULLY CLOSED AND TOPS IN A VERTICAL POSITION. TABLE TOPS ARE HEAVY - DO NOT ATTEMPT TO ASSEMBLE ALONE! 2. Attach table top (#19) to table base that you just assembled, as shown in Figure 2. With at least one adult on each side of table top (#19), lift top and align ends of "U"-support tube with top of pivot tubes on caster rails (#1). Slide tubes together. 3. With two adults, put other table top onto other pivot tubes following instructions in step 2. DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE INSTALLED!IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE. 4. Attach corner protectors (#32) to rails using tree plugs (#22). Simply push the plugs through the protector and into the rail until snug. 3 NET ASSEMBLY Net System Description 1. Net Post Assembly Attach plastic net post as shown with washer and knob. Note: there is a left and right net post assembly (See Net System Description). Post assembly should rest flat against nut plate. Slide the net sleeve over the vertical post while the net post assembly is folded in toward the side of the table top. Fold the net post assembly out against the net post stop into the post and secure bead chain in catch. 2. [. . . ] Continue to pull until disengaged from safety clips and legs rest on the floor. Do not leave table partially opened at midway position. See Figure 3. TO CLOSE: Caution: To prevent damage to the net system and/or table top, the post assembly must be pivoted toward side of table before lifting table tops to storage position. Lift table half to midpoint until the safety clips are engaged. [. . . ]