User manual ESCALADE SPORTS 2L-6753-02

[. . . ] 6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. · · · · · Do not dunk on this unit Do not hang from any part of the unit, including the backboard, rim, support braces, or net. Keep organic material away from pole base. [. . . ] Tightening hardware too tight may damage tubing and make adjustment of system difficult. Slide Actuator Sleeve (#15) over Actuator (#16) and place Actuator Cap (#13) on top. Slide Pivot Tube (#14) in hole near the top of Actuator until equal amounts stick out on both sides of Actuator. NOTE: It may be necessary to use a hammer or rubber mallet to tap in Spacer. 1. Figure 3 2. Figure 4 Lay Pole (#2) on its side on two padded saw horses. Attach Actuator (#16) to Pole (#2) using one bolt (#19), split lockwasher (#18), washer (#3) and two plastic washers (#5) to thread into each side of Actuator. Insert Pole Cap (#1) into top of Pole (#2). It may be necessary to use a hammer or rubber mallet to tap Cap in. 3. 4. Attach lower arm (#11) to Pole (#2), as shown in Figure 4, using a bolt (#8), two flatwashers (#3), four nylon washers (#5) and hex nut (#4). Note: make sure "Goalrilla lettering is right side up. Secure Actuator (#16) to Lower Arm (#11) using one bolt (#8), two flatwashers (#3), four nylon washers (#5) and one hex nut (#4). Tighten both bolts (#8) securing Lower Arm (#11). Note: Tighten bolts snug but, do not over tighten. If the four Tube Plugs (#10) are not already installed insert them into open ends of Lower Arm (#11). It may be necessary to use a hammer or rubber mallet to tap plug in. 6 5. Figure 5 Attach Upper Arm (#6) to Pole (#2), as shown in Figure 6, using a bolt (#7), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: Tighten bolts snug but, do not over tighten. If the four Tube Plugs (#9) are not already installed insert them into open ends of Upper Arm (#6). It may be necessary to use a hammer or rubber mallet to tap plug in. 7. PLACING THE POST ON THE ANCHOR SYSTEM REQUIRES AT LEAST FOUR CAPABLE ADULTS. POLE WILL WANT TO LEAN WHILE ATTEMPTING TO STAND IT UP ON ANCHOR BOLTS. Figure 6 Figure 7 9. BE SURE CONCRETE HAS BEEN ALLOWED TO CURE FOR AT LEAST 3 DAYS Locate hardware needed to mount pole to anchor bolts. You will need, eight flatwashers (#37), four lock washers (#36), four hex nuts (#35) and four thread protectors (#34). 10. Put a flat washer (#37) on each anchor bolt. Lift post onto anchor system and secure with one flatwasher (#37), one lock washer (#36) and one hex nut (#35) for each anchor bolt. [. . . ] ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS. EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE. Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above limitations or exclusions may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. WARRANTY GUIDELINES IS REQUIRED FOR ALL WARRANTY CLAIMS 1. [. . . ]