User manual ESCALADE SPORTS 2L-7039-02

[. . . ] MODEL NO. B 3300W Goalrilla III BASKETBALL SYSTEM OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. Some smaller parts may be shipped inside larger parts. [. . . ] The top four nuts remain on bolts and are used for leveling. Let concrete stand for a MINIMUM of 72 hours. Figure 2 Figure 2 Figure 4 5 ASSEMBLY INSTRUCTIONS (Day 5) IMPORTANT!Nylon washers (#5) adequately space painted parts at all pivot points. Neglecting the use of these washers will result in rusted parts. 46 NOTE: All board arms are made of rectangular tubing. Tightening hardware too tight may damage tubing and make adjustment of system difficult. Using Allen Wrench (#45) provided, attach Post Brackets (#44) to outside of brackets on back of Post Assembly (#2). Secure with two Flat Head Screws (#46), two Flat Washers (#26) and two Locknuts (#33) in each Bracket (#44). See Figure 3. 44 2 2 44 26 33 26 46 2. Slide Actuator Sleeve (#15) over Actuator (#16) and place Actuator Cap (#13) on top. Slide Pivot Tube (#14) in hole near the top of Actuator until equal amounts stick out on both sides of Actuator. NOTE: If necessary, use a hammer or rubber mallet to tap in Spacer. 19 18 3 5 Figure 3 3. Lay Pole (#2) on its side on two padded saw horses. Secure Actuator (#16) to Pole (#2) using one bolt (#19), split lockwasher (#18), washer (#3) and two plastic washers (#5) to thread into each side of Actuator. Insert Pole Cap (#1) into top of Pole (#2). It may be necessary to use a hammer or rubber mallet to tap Cap in. 5 Figure 4 15 16 14 13 3 18 19 4. 2 1 2 8 3 5 11 Figure 5 5. Attach lower arm (#11) to Pole (#2), as shown in Figure 5, using a bolt (#8), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: make sure "Goalrilla" lettering is right side up. Do NOT tighten bolt (#8) at this time. 5 5 3 4 6 8 10 5 3 5 Secure Actuator (#16) to Lower Arm (#11) using one bolt (#8), two flatwashers (#3), four plastic washers (#5) and one hex nut (#4). Tighten both bolts (#8) securing Lower Arm (#11). Note: Tighten bolts snug but, do not over tighten. If the two Tube Plugs (#10) are not already installed insert them into open ends of Lower Arm (#11). It may be necessary to use a hammer or rubber mallet to tap plug in. 7 6. 5 3 4 2 11 3 5 2 Figure 6 8. Attach Upper Arm (#6) to Pole (#2), as shown in Figure 7, using a bolt (#7), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: Tighten bolts snug but, do not over tighten. If the two Tube Plugs (#9) are not already installed insert them into open ends of Upper Arm (#6). [. . . ] WARRANTY COVERAGE: Escalade® Sports warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL OR WORKMANSHIP . Subject to proper installation and normal use, Escalade® Sports warrants, subject to the limitations below, to the original retail purchaser all structural components of the GoalrillaTM System to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Merchandise must be shipped prepaid with a copy of proof of purchase to Escalade® Sports factory for examination to determine if the basketball system needs to be repaired or replaced. [. . . ]