User manual ESCALADE SPORTS 2L-7068-00

[. . . ] Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable wrench may be substituted for the wrenches), Flat Blade Screw Driver Please Do Not Return This Product To The Store! Contact Escalade® Sports customer service department at: Phone: 1-866-873-3528 Toll ­ Free !E-mail: tabletennis@escaladesports. com Mailing Address (correspondence only): Escalade Sports PO Box 889 Evansville, IN 47706 Please visit our World Wide Web site at: www. escaladesports. com ON-LINE TROUBLE SHOOTING ON-LINE PARTS REQUESTS TECHNICAL ASSISTANCE FREQUENTLY ASKED QUESTIONS ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION 2L-7068-00 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. © 2006Escalade® Sports CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE ASSEMBLY! [. . . ] NOTE: Spacer #20 goes between leg and linkage. Tighten locknuts snug, but do not overtighten. You are now done assembling parts to the first table half. Repeat steps 8 ­ 11 on second table half. CAUTION: UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THEIR OWN. IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE HALVES. TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER Figure 7 13. Place a Hex Bolt #22, a Washer #27 and a Locknut #26 on the floor next to all four caster wheels on both sides of base assembly you put together earlier. Make sure the leg assembly #9 on the first table half is open and linkages #16 are pointing toward middle of table. With one adult person on each side of the table, lift and set table half on its legs. While holding table half up, pull the base assembly under this half until the hole in Upright Tube #15 is aligned with lower middle hole in the Mounting Bracket #6 on the bottom of table half. Attach Upright Tubes #15 to Mounting Brackets #6 with Hex Bolts #22, Washers #27 and Locknuts #26 that you placed on floor in step 13. Remove bottom bolts #21 from bottom holes that attach name panels to Upright Tubes. Attach end of Linkage #16 to outside of Upright Tube #15 with bolt #21 (that you just removed), spacer #20 and Locknut #26. Note spacer #20 goes between linkage #16 and upright tube #15. Tighten all nuts snug, but do not overtighten. Joints must pivot. CAUTION: TABLE HALF WILL NOT STAND ON ITS OWN, YOU MUST HOLD IT UP! Brace table half against a wall to help stabilize it. Be sure that there is enough room to connect second half. CAUTION: DO NOT ATTEMPT TO RAISE THIS HALF UP TO STORAGE POSITION UNTIL OTHER HALF TOP IS ATTACHED AND YOU HAVE READ AND UNDERSTAND ALL OPERATING INSTRUCTIONS. 5 CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE FOLLOWING STEPS! Figure 8 16. With first table half (that you just attached) braced against a wall, attach second table half. Make sure the leg assembly #9 on the second table half is open and linkages #16 are pointing toward middle of table. With one adult person on each side of the table, lift and set table half on its legs. 17. Remove bottom bolts #21 from bottom holes that attach name panels to Upright Tubes. Attach end of Linkage #16 to outside of Upright Tube #15 with bolt #21 (that you just removed), spacer #20 and Locknut #26. Note spacer #20 goes between linkage #16 and upright tube #15. [. . . ] This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or blister. UNLEVEL FLOORS If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the best location for the table. [. . . ]