User manual ESCALADE SPORTS G0110

[. . . ] Call us at: 1-800-426-1421 (THIS IS A CONSUMER ONLY NUMBER) FAX: 812-467-1399 OR WRITE TO: ESCALADE SPORTS CUSTOMER SERVICE DEPARTMENT P. O. BOX 889 EVANSVILLE, IN 47706 When contacting Escalade Sports please provide model number, serial number (if applicable), and part number if requesting a replacement part. These numbers can be found on the product, packaging, and in this Owner's Manual. 1 REQUIRED TOOLS PHILLIPS SCREWDRIVER STANDARD SCREWDRIVER ADJUSTABLE WRENCH OR STANDARD SOCKET SET 2 0110-C11 PARTS IDENTIFIER HARDWARE (ACTUAL SIZE MAY VARY) DESCRIPTION (EXTRA PIECES MAY BE INCLUDED) QTY. REQUIRED H1 5/16" X 1 1/4" BOLT 16 H2 H3 H4 H5 H6 H3 PART NOT SHOWN ACTUAL SIZE. 5/16" WASHER, BLACK FLAT 1/4" X 24 7/8" ROD 16 2 1/4" WASHER, FLAT 4 1/4" LOCK NUT 4 3/16" X 1 3/4" BOLT 8 H7 H8 3/16" WASHER, FLAT 8 5/8" SHORT PHILLIPS HEAD SCREW 3 10 PARTS IDENTIFIER ASSEMBLY PARTS DESCRIPTION QTY P1 P2 SIDE PANEL 2 END PANEL 2 P3 P4 P5 P6 P7 P8 P9 PLAYING FIELD 1 RIGHT LEG 4 LEFT LEG 4 PLAYING FIELD SUPPORT BRACE 3 ROD HANDLE 8 ROD END CAP 8 BALL CATCHER 4 2 0110-C11 PARTS IDENTIFIER ASSEMBLY PARTS DESCRIPTION QTY R1 R2 R3 R4 R5 R6 4 YELLOW PLAYER ROD 3 YELLOW PLAYER ROD 1 2 2 YELLOW PLAYER ROD 1 4 BLUE PLAYER ROD 1 3 BLUE PLAYER ROD 2 2 BLUE PLAYER ROD 1 ACCESSORIES DESCRIPTION QTY A1 A2 A3 SOCCER BALL 2 TOOL 1 TOOL 2 5 PARTS IDENTIFIER PRE-ASSEMBLED PARTS DESCRIPTION QTY C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 4 PLAYER ROD 2 3 PLAYER ROD 4 2 PLAYER ROD 2 ROD SPRING 16 ROD WASHERS 32 10-24 X 7/8" BOLT (used to install men) 26 10-24 LOCKING NUT (used to install men) 26 BLUE MEN YELLOW MEN 13 13 ROD BUSHING 6 32 0110-C11 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE IMPORTANT: Please read through the instruction book before attempting assembly to familiarize yourself with all parts and assembly steps. [. . . ] SEE figure 1B. P1 STEPS 1-2 HOLE 3 YELLOW PLAYERS ROD R2 2 YELLOW PLAYERS ROD R3 3 BLUE PLAYERS ROD R5 4 YELLOW PLAYERS ROD R1 4 BLUE PLAYERS ROD R4 3 YELLOW PLAYERS ROD R2 2 BLUE PLAYERS ROD R6 3 BLUE PLAYERS ROD R5 FIGURE 1A STEP 3 P1 P3 P1 FIGURE 1B 8 0110-C11 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE 4. ATTACH THE TWO END PANELS P2 TO THE SIDE PANELS P1 AS SHOWN IN figure 2. REMEMBER THE GROOVE MUST FACE INWARD TOWARD THE PLAYFIELD. ATTACH THE END PANELS WITH BOLTS H6 AND WASHERS H7 INTO THE PRE-INSTALLED DOWEL CONNECTORS. TIGHTEN HARDWARE AT THIS TIME CAUTION: Do not over-tighten hardware!PLACE THE PLAYFIELD SUPPORTS P6 ON THE BOTTOM OF THE PLAYFIELD. INSERT SUPPORT RODS H3 THROUGH THE HOLES IN THE SIDE PANELS AND THE GROVE IN THE PLAYFIELD SUPPORTS P6 AS SHOWN IN figure 3. PLACE WASHER H4 AND LOCKNUT H5 ON EACH END OF SUPPORT RODS H3. P1 STEP 4 P3 P2 P1 H7 H6 FIGURE 2 STEP 4 H4 P6 H3 H5 FIGURE 3 9 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE 6. THERE ARE TWO RIGHT LEGS P4 AND TWO LEFT LEGS P5. THE WIDER SIDE OF THE LEG IS BOLTED TO THE SIDE PANELS P1. THE LEGS ARE ATTACHED WITH BOLTS H1 AND WASHERS H2. THE THREADED T-NUTS ARE PRE-ASSEMBLED IN THE LEGS. TIGHTEN HARDWARE AT THIS TIME. CAUTION: Do not over-tighten hardware! WARNING: This step requires two adults!Very carefully turn the table over and set on its legs. Be careful. The table is very heavy and the rods will slide. Do not lift the table by holding onto the rods. P5 STEP 6 P4 P4 H1 H2 P5 FIGURE 4 10 0110-C11 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE 7. ATTACH BALL CATCHERS P9 TO THE SIDE PANELS AS SHOWN IN figure 2 USING SCREWS H8. SLIDE THE HANDLES P7 ONTO THE END OF THE RODS WITH THE HOLE CLOSE TO THE END. SLIDE THE RUBBER END CAPS P8 ONTO THE OTHER ENDS OF THE RODS. CAREFULLY CUT THE RUBBER BANDS THAT HOLD THE BUSHING ASSEMBLIES TOGETHER ON THE RODS. HINTS: If the rods do not slide freely you can spray furniture polish on a rag and wipe down the rods. [. . . ] If a ball is spinning in place, it is not considered a dead ball. 12 0110-C11 90 DAY WARRANTY Manufacturer warrants to the original retail purchaser, this product to be free from defects in material and workmanship for a period of ninety (90) days from the date of purchase. Should this product become defective due to material or workmanship within the warranty period, contact our Customer Service Department. This warranty is not transferable and does not cover normal wear and tear, or damage caused by improper handling, installation, or use of this product. This warranty is also void if product is in any way abused, damaged, or modified from its original state, or if used for other than indoor residential use. [. . . ]