User manual ESCALADE SPORTS G01221

[. . . ] PARTS IDENTIFIER HARDWARE ( ACTUAL SIZE MAY VARY ) DESCRIPTION QTY. REQUIRED (EXTRA PIECES MAY BE INCLUDED) H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 5/16" x 1-3/4" BOLT 16 5/16"WASHER, BLACK FLAT 16 1/4"x25-5/8"SUPPORT ROD 1/4" WASHER, BLACK FLAT 1/4"x1-1/4" BOLT 1/4"x1/2" FINISHING NUT 3/8" WASHER, BLACK FLAT 1"FLAT HEAD SCREW 3/4"FLAT HEAD SCREW 1/2"ROUND HEAD SCREW 5/8"ROUND HEAD SCREW 3 12 12 6 6 4 8 14 4 For Customer Service Call 800-426-1421 3 PARTS IDENTIFIER ASSEMBLY PARTS P1 P2A P2B P3 P4 P5 P6 P7 P8 P9A P9B P10 P11 P12 ( ACTUAL SIZE MAY VARY ) QTY DESCRIPTION SIDE PANEL END PANEL WITHOUT HOLES END PANEL WITH HOLES 2 1 1 PLAYFIELD LEG PLAYFIELD SUPPORT BRACE 1 4 3 ROD HANDLE ROD END CAP BALL ENTRY CUPS BALL CATCHER (Long Wire) BALL CATCHER (Short Wire) 8 8 2 1 1 WIRE CLIP 3 ELECTRONIC SCORER SLIDE SCORER 1 2 For Customer Service Call 800-426-1421 PARTS IDENTIFIER ACCESSORIES DESCRIPTION QTY A1 A2 A3 SOCCER BALL TOOL TOOL 4 1 2 ASSEMBLY PARTS DESCRIPTION QTY R1 R2 R3 R4 R5 R6 4 PLAYERS ROD (COLOR 1) 1 2 1 3 PLAYERS ROD (COLOR 1) 2 PLAYERS ROD (COLOR 1) 4 PLAYERS ROD(COLOR 2) 1 3 PLAYERS ROD (COLOR 2) 2 2 PLAYERS ROD (COLOR 2) 1 For Customer Service Call 800-426-1421 PARTS IDENTIFIER REPLACEMENT PARTS DESCRIPTION QTY C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 4 PLAYER ROD 2 3 PLAYER ROD 2 PLAYER ROD BUSHING 4 2 16 5/32"x1"BOLT (used to install men) LOCK NUT (used to install men) 24 24 PLAYER(COLOR 1) 12 PLAYER (COLOR 2) 12 ROD BUSHING PLASTIC ROD WASHER 16 16 For Customer Service Call 800-426-1421 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE Please read through the instruction book before attempting assembly to familiarize yourself with all part and assembly steps IMPORTANT: 1 CUT CORNERS OF THE BOX AND PLACE IT ON THE FLOOR TO PROTECT THE PARTS AS THE UNIT IS BEING ASSEMBLED . [. . . ] REMEMBER: THE GROOVE MUST FACE INWARD TOWARD THE PLAYFIELD . ATTACH THE END PANELS WITH BOLTS H5 AND WASHERS H4. TIGHTEN ALL HARDWARE AT THIS TIME. 5 PLACE THE PLAYFIELD SUPPORTS P5 ON THE BOTTOM OF THE PLAYFIELD. INSERT SUPPORT RODS H3 THROUGH THE HOLES IN THE SIDE PANELS P1 AND THE GROOVE IN THE PLAYFIELD SUPPORTS P5 AS SHOWN IN FIGURE 3 . PLACE WASHER H7 AND FINISHING NUT H6 ON EACH END OF SUPPORT RODS H3. 6 ATTACH THE PLAYFIELD P3 TO THE END PANELS P2 AND P2A WITH 3/4" FLAT HEAD PHILLIPS SCREWS H9 STEP 4 P1 P3 P2A P1 H4 H5 H9 P2B FIGURE 2 P5 STEP 5, 6 H6 H3 FIGURE 3 H7 For Customer Service Call 800-426-1421 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE ATTACH EACH LEG P4 USING FOUR BOLTS H1 AND FOUR WASHERS H2 DO NOT OVERTIGHTEN 8 ATTACH GOAL BOXES P9A AND P9B TO THE END PANELS P2A AND P2B WITH SCREWS H9 AS SHOWN IN figure 4. THE GOAL BOX WITH THE LONGEST WIRE GOES OPPOSITE THE END PANEL WITH THE TWO HOLES ABOVE THE BALL RETRIEVAL HOLE IMPORTANT!MAKE SURE YOU PUSH THE WIRES INTO THE HOLES IN THE TOP OF THE END PANEL BEFORE YOU ATTACH GOAL BOX P9A. 9 ATTACH THE LONG WIRE TO THE BOTTOM OF THE TABLE USING ONE CLIP P10 AND SCREW H9 INTO EACH PLAYFIELD SUPPORT BRACE. NOTE: THE SCREWS MUST BE PUT IN THE SUPPORT BRACE. DO NOT ATTACH SCREWS INTO THE PLAYFIELD. THE PURPOSE IS TO HOLD THE WIRE OUT OF THE WAY SO IT CANNOT BE PULLED FROM THE GOAL BOX. Very carefully turn the table over and set on its legs. The table is very heavy and the rods will slide. Do not lift the table by holding onto the rods. STEPS 7, 8, 9 P4 P9 P9A H10 P2A P9B H10 FIGURE 4 H1 H10 P10 H1 H2 H1 For Customer Service Call 800-426-1421 SOCCER TABLE ASSEMBLY ASSEMBLY INSTRUCTIONS WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE 10 ONCE YOU ARE SURE THE RODS ARE INSTALLED CORRECTLY, SLIDE HANDLES P6 ONTO THE ENDS OF THE RODS WITH THE HOLE CLOSET TO THE END. [. . . ] TURN UNIT OFF AND UNPLUG UNIT WHEN NOT IN USE. NOTE: ELECTRONIC SCORER WILL NOT WORK PROPERLY UNLESS ATTACHED TO THE TABLE WITH BOTH GOAL WIRES PLUGGED IN. STEP 12 P11 H11 FIGURE 6 For Customer Service Call 800-426-1421 12 [. . . ]