User manual ESCALADE SPORTS G07603

[. . . ] We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-866-556-2759 FAX: 1-866-873-3531 customerservice@escaladesports. com Or write to: Escalade Sports Customer Service Department P. O. Box 889 Evansville IN 47706 Please have your model number when inquiring about parts. When contacting Escalade Sports please provide your model number, serial number (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and in this owners manual. [. . . ] (Only the four countersunk holes in the center of the table need to be filled since the other holes will be covered by the rails. ) Do not use more grout than is necessary. Allow grout to cure before starting the next step. Using a medium (80) grit sandpaper and a sanding block, lightly sand the filled areas smooth and flat. RECHECK THESE AREAS TO MAKE SURE THEY ARE FLAT. Apply grout again if you still find low places at countersunk holes or seams. © 2003 Escalade Sports 14 For Customer Service Call 1-866-556-2759 Step 33 Step 34 © 2003 Escalade Sports 15 For Customer Service Call 1-866-556-2759 Step 35 Step 36 Use the following details for the correct meathod of cutting the pocktets. © 2003 Escalade Sports 16 For Customer Service Call 1-866-556-2759 Step 37 Step 38 © 2003 Escalade Sports 17 For Customer Service Call 1-866-556-2759 Step 39 Top Rail Identifier Figure 8 © 2003 Escalade Sports 18 For Customer Service Call 1-866-556-2759 Assembling Rails to the Pockets 40. Find the 3/4 inch holes in the playing surface that are between each pocket and cut a small cross in the cloth over each hole for bolts to pass through. Carefully turn an end rail P16, left hand rail P14 and right hand rail P15 face down on the table surface. (See figure 9) Care must be used to avoid scratching rail finish. Find two corner pockets P12, four bolts H10 and four washers H4. Attach corner pockets to rails by inserting pocket posts into the rail ends. (See figure 9) Pull rail ends snugly against pocket edges before tightening bolts. Repeat procedure using the other end, left and right hand rails. Find two center pockets P13, four bolts H10 and four washers H4. Connect the rail assemblies to the side pockets. (See figure 9) Snug rails against pocket edges before tightening bolts H10. With the aid of two other adults CAREFULLY turn the rail assembly over. Align assembly on the table's playfield with an equal amount of overhang around the table. Figure 9 44. When calling the shot, it is never necessary to indicate details such as the number of cushions, banks, kisses, caroms, etc. Any balls pocketed on a foul remain pocketed, regardless of whether they belong to the shooter or the opponent. The opening break is not a" called shot. " Any player performing a break shot in 8-Ball may continue to shoot so long as any object ball is legally pocketed on the break. RACKING THE BALLS The balls are racked in a triangle at the foot of the table with the 8-ball in the center of the triangle, the first ball of the rack on the foot spot, a stripe ball in one corner of the rack and a solid ball in the other corner. ALTERNATING BREAK Winner of the lag has the option to break. [. . . ] BAD HIT If the first object ball contacted by the cue ball is not the lowest numbered ball on the table, the shot is foul. NO RAIL If no object ball is pocketed, failure to drive the cue ball or any numbered ball to a rail after the cue ball contacts the object ball on is a foul. IN HAND When the cue ball is in hand, the player may place the cue ball anywhere on the bed of the table, except in contact with an object ball. The player may continue to adjust the position of the cue ball until shooting. [. . . ]