User manual ESCALADE SPORTS M01471-2003

[. . . ] Do not overtighten hardware, as you could crush the tubing. Some drawings or images in this manual may not look exactly like your product. You may need to move the unit if it does not perform correctly. Sunlight or Halogen lighting may have an effect on the infrared sensors performance. [. . . ] ONCE ALL TUBES ARE IN PLACE TIGHTEN ALL HARDWARE FROM THE PREVIOUS 4 STEPS. Figure 4 © 2003 Escalade Sports 8 For Customer Service Call 1-888-996-2729 Note: Please use the diagram at the bottom of the page for the correct wiring sequence for the sensors. Attach two rims P14 to the backboard P13 using bolts H2, washers H10, plastic spacer plate P23 and nuts H11 as shown in FIGURE 5. The spacer goes between the rim and the backboard. Peel the protective coating from the electronics P15 and attach them to the backboard P13 using bolts H7, washers H8 and nuts H9. Attach the sensors to the backboard using screws H6. There are three sensors per rim. Peel the protective coatingfrom the back board before attaching electroinics Figure 5 © 2003 Escalade Sports 9 For Customer Service Call 1-888-996-2729 10. Find the top of the ramp netting and slide over the P11 tubes as shown in FIGURE 6. Figure 6 TWO ADULTS ARE REQUIRED TO COMPLETE THE BACKBOARD INSTALLATION. © 2003 Escalade Sports 10 For Customer Service Call 1-888-996-2729 11. Attach the backboard and ramp net to the frame using bolts H3, washers H10, plastic lipped washers H12, and nuts H11 as shown in FIGURE 7 except for the bottom hole on the backboard you will also attach the ramp as shown in DETAIL A. Make sure you put the ramp behind the horizontal bar P9. Figure 7 12. Slide support tube P9 through the bottom of the ramp net and attach using bolts H1 washers H10 and Nuts H11. Attach the velcro strap P21 around the tubes under the backboard as shown. this is to be used to hold the unit together when folded in the storage position. © 2003 Escalade Sports 11 For Customer Service Call 1-888-996-2729 12. Attach the nylon cord P22 as shown in FIGURE 8. This will allow one person to be able to fold the unit into storage position. Feed the cord through the open hole in P2A, through the ring on P2 and back to the ring on P2A. Figure 8 Congratulations!Please note the Care and Use instructions below to insure many years of trouble free use of your game table. CARE AND USE OF YOUR GAME 1. Plug the adapter into a suitable 120v AC household outlet. This product is intended for INDOOR use only. This will damage the legs © 2003 Escalade Sports 12 For Customer Service Call 1-888-996-2729 ADJUSTMENT AND USE OF YOUR SHOTCLOCK Plug the adapter into a suitable 120v household outlet and into the back of the scoring unit. Set the switch in the back of the unit to "TEST". When in "test" mode your scorer should have 88 showing for each players score. The 88 on the left is for the top two sensors and the 88 on the right is the bottom sensor. [. . . ] WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMANSHIP. WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADE SPORTS shall repair or replace with a comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept. Or Write us at: Escalade® Sports, Inc. [. . . ]