User manual ESCALADE SPORTS M01477-BOOKLET

[. . . ] However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: D A C 1-888-996-2729 FAX: 1-866-873-3535 arcadegames@escaladesports. com Or write to: Escalade Sports Customer Service Department P. O. Box 889 Evansville IN 47706 B Please have your model number when inquiring about parts. When contacting Escalade Sports please provide your model number, serial number (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and in this owners manual. P15 Your Model Number _______________________ M01477 4 © 2003 Escalade Sports 1 For Customer Service Call 1-888-996-2729 IMP OR TANT !R E AD T HIS MANUAL ALL T HE WAY T HR OUG H B E F OR E B E G INNING TO P UT Y OUR G AME TAB LE TOG E T HE R ! [. . . ] We recommend building the unit on the box top to protect the parts during assembly. Place the main cabinet P1 up side down as shown in FIGURE 1. Attach the goalie handle P3 to the main cabinet using bolt H2, two washers H4 and lock nut H3. Do not over tighten, the handle must be able to pivot. Attach the puck catcher P2 to the cabinet using screws H1 as shown in FIGURE 1. Repeat steps 3 and 4 for both ends of the table. 6. From the bottom of the table insert a gear assembly P10 into each player groove. You want the playfield between the two flat tabs on the gear. You do this by putting the tabs into the player groove and then turning the entire gear assembly so it faces the rod it will be attached to. Next push the gear assembly into the corresponding rod and attach with screw H1. Also attach the rod stopper P11 to the rod with screw H1. Slide one rubber bushing P9 onto each rod from outside of the main cabinet. Slide a rod handle P8 on the rod after the rubber bushing. H1 P11 P3 Goalie Handle H1 Screw P2 Puck Catcher H2 Bolt H4 Washer H3 Lock Nut P6 Player Rod C P5 Player Rod A P4 Player Rod D P7 Player Rod B Figure 1 P7 Player Rod B P5 Player Rod A P8 Rod Handle P9 Rubber Bushing P4 Player Rod D Figure 2 6 © 2003 Escalade Sports 7 For Customer Service Call 1-888-996-2729 PRODUCT P ARTS LIST Part # H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 P1 P2 P3 P4 P5 P6 P7 P8 P9 Description Qty 26 2 18 36 16 16 16 8 1 1 4 1 2 2 4 2 2 2 10 10 Part # P10 P1 1 P12 P 13 P14 P15 P 16 P17 P 18 P 19 P20 P21 P22 P23 A1 A2 A3 C1 C2 1/2 Round Head Screw 3/16 x 5/8 Bolt 3/16 Lock Nut 3/16 Flat Washer 5/16 x 1-3/4 Bolt 5/16 Flat Washer 3/16 x 1" Bolt 5/8 Round Head Screw Allen W rench Open End Wrench 5/8 Flat Head Screw Main Cabinet Puck Catcher Goalie Handle Player Rod D Player Rod A Player Rod C Player Rod B Rod Handle Rubber Bushing M01477 Qty 10 10 4 2 2 2 1 4 1 1 4 1 1 2 4 10 10 1 1 1 4. Attach the goal P 15 to each end of the table with screw H8 as shown in FIGURE 4. 15. Attach the hockey scorer P23 with screws H11 Description Gear Assembly Rod Stopper Leg Side Leg Panel End Leg Panel Goal Long Stick Player Red Short Stick Player Red Red Goalie Long Stick Player Blue Short Stick Player Blue Blue Goalie Support Brace Scorer Puck Rod Bushing Front Rod Bushing Rear Hardware Kit Owners Manual H11 Screws P23 Scorer P15 Goal H8 Screw PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. STORE THE MANUAL IN THE MANUAL STORAGE BAG LOCATED UNDER YOUR TABLE. Figure 4 R ev 01 12 © 2003 Escalade Sports 9 For Customer Service Call 1-888-996-2729 15. S lide the players onto the metal tabs on the gear as s emblies . S et the players as s hown below in F IG UR E 5. Note that there is one long s tick blue player and one long s tick red player. [. . . ] Or Write us at: Escalade® Sports, Inc. Box 889, Evansville, IN 47706 Attn: Warranty Dept. Or E-mail us at: arcadegames@escaladesports. com Other than shipping requirements no charge will be made for such repair or replacement of inwarranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for value prior to mailing. WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ABOVE 90 DAY PERIOD. [. . . ]