User manual EUTECH INSTRUMENTS CYBERCOMM PRO FOR CYBERSCAN CON 1500

[. . . ] Data type stored is in the ASCII format. © Windows is the registered trademark of Microsoft Corporation 1. 2 System Requirements To run the CyberComm Pro DAS software, the following items are required: 1 2 3 4 IBM Compatible PC Pentium and above Windows Operating Systems 95 and above VGA/SVGA Monitor RS232C Serial Communication Cable 1. 2. 1 Setting the Communication Parameters The meter is capable of different communication configurations for baud rate, parity and stop bits. The values chosen for these parameters of the meter must match those chosen for the computer, same goes for the serial printer if it is connected. 1 Instruction Manual CyberComm CON 1500 2 2. 1 INSTALLATION OF CYBERCOMM DATA ACQUISITION SOFTWARE (DAS) Loading of CD-ROM See Figure 1. Before running the program, check that the CyberScan CON 1500 meter is properly connected to the computer. It is preferable to connect to either one of the COM (serial) ports available on a computer. [. . . ] After matching the Communication Settings and setting the Data Log Options between your computer and the CyberScan CON 1500 meter using CyberComm Pro, you can now capture data into your computer for analysis and storage purposes. EXAMPLE: Set Time between successive readings to be `10 sec', Length of Time to Capture Data to be `5 min'. You will be able to retrieve the recorded data in every 10 seconds during a 5 minutes duration measurement. Reference source not found. : Retrieve Recorded Data. 3. 3 Connect to Meter (File) See Figure 8. From the Main Menu, select Connect to Meter to start the communication between your computer and the meter. The complete main window the CyberComm Pro will start after connection to the meter: NOTE: All keys on the meter are disabled after connection to computer. 6 Instruction Manual CyberComm CON 1500 4 4. 1 MAIN WINDOW (AFTER CONNECTING METER TO COMPUTER) CyberComm Pro Manuals (Help) See Figure 8 and 9. The main menu appears with the File and Help drop down menus, each having a list function settings shown below. Soft copies of the CyberComm Pro Software User Guide Manuals are available in the program itself. Select the manual option with reference to the meter you are using. Figure 8:Running CyberComm Pro/ Complete Main Menu (Connected to meter) Figure 9: CyberComm Pro Main Menu (Partial) 7 Instruction Manual CyberComm CON 1500 4. 1. 1 File Options (File) See Figure 10. Select File Options from the File drop down menu. Enter the relevant information for useful future references and type a file name/or file location that you wish to store these details. Click OK upon completion to save information. Figure 10: File Options 4. 1. 2 About CyberComm Pro (Help) See Figure 6. By selecting About CyberComm Pro from the Help drop down menu, the dialogue box will be shown as below. It tells you the version of the CyberComm Pro Program you are using. Select OK button to exit. Figure 11: About CyberComm Pro 8 Instruction Manual CyberComm CON 1500 4. 2 Sub menus & Function Icons on the CyberComm Program See Figure 12. The figure shows the CyberComm Pro software Main Menu after linking with the meter. From this menu, most of the meter key functions can be emulated except replatinisation of conductivity probe. This Sub Menu has following features: Figure 12: Running CyberComm Pro/ Complete Main Menu (Connected to meter) NOTE: All keys on the meter are disabled after connection to computer. 9 Instruction Manual CyberComm CON 1500 4. 2. 1 Function Icons See Figure 13. The function icons on the main menu each serve a vital role in the CyberComm Pro software, providing user friendly one click access. Figure 13: Function Icon Panel (extracted from Figure 12) Icon no. 1 Function Name Description Click on this icon to start recording meter readings, readings will be shown on the CyberComm Pro main menu. Data captured will also be stored to the hard disk (in a ". csv" formatted file). A pop-up menu will prompt you whether to overwrite saved data should you already have recorded data reading. New data should be saved under a NEW file name. Works together with the `Pause Tracking' icon. [. . . ] Open a new document in the Microsoft Word© 2. Select `Edit' from the menu and click `Paste' to transfer data from the clipboard to the current word document. The data will be displayed as shown below. Figure 21: Paste data readings in a Microsoft Word© document 17 Instruction Manual CyberComm CON 1500 6. 3 Paste data in Microsoft Excel© , WordPad and Notepad Follow steps instructed in Section 6. 1: Steps to export data readings from CyberComm Professional: and paste the data copied from the CyberComm Pro to a new document. Figure 22: Paste data readings in a Microsoft Excel© document 18 Instruction Manual CyberComm CON 1500 Figure 23: Paste data readings in a Microsoft Notepad© document 19 Instruction Manual CyberComm CON 1500 7 7. 1 PRINT READINGS Printing using a serial printer Connect the CyberScan CON 1500 bench meter to the serial printer via RS232C cable (refer to the list of accessories). The configuration of the RS232C port is as shown below. [. . . ]