User manual EVOLUTION MK361

[. . . ] Press the numeric keys to alter the PROGRAM CHANGE number. You can also use the "+" or "-" keys to change the value. Note: * if you don't do anything for 5 seconds the LED stops flashing and shows the current PROGRAM CHANGE number. * if the number you press is larger than 127, it will return to the previous PROGRAM CHANGE number. 5. PROGRAM & BANK CHANGE MEMORY You can assign a selected PROGRAM CHANGE as well as a BANK LSB and a BANK MSB to one of ten numeric keys (0-9). Once stored, simply pressing one of the numeric keys will send the desired PROGRAM and BANK CHANGES. [. . . ] * When you assign 120 or 121 as the MIDI controller for the WHEEL, you should move the MODULATION Wheel to the mid-value then return it to the minimum value to send a relative MIDI message. * See Appendix B for a full list of controller numbers. 8. PITCH BEND WHEEL Moving the PITCH BEND WHEEL transmits MIDI PITCH BEND messages to any connected equipment. This allows you to bend the pitch of a sound up (or down one tone) to add expression to your performance. · · To bend the sound up: Move the WHEEL away from you. To bend the sound down: Move the WHEEL towards you. 9. WHEEL ASSIGN Use the WHEEL to transmit MIDI CONTROL CHANGE messages. You can select and assign 119 types of MIDI functions (1-31, 33-95, 102-121, 128-132) Number 1 ­127 128 129 130 131 132 · · Note: Functions Standard MIDI controllers Pitch Bend Sensitivity Fine Tune Coarse Tune Channel Pressure Velocity Press the WHEEL ASSIGN switches (MEMORY & PROGRAM) together and the LED starts to flash showing the number of the present MIDI controller. Use numeric keys 0-9 to select a new MIDI controller. You can also use the +/- switches to increase or decrease the value of the number. * If you do nothing for 5 seconds, the LED will return to show the current PROGRAM CHANGE number. * If the number you press is not in the range of defined numbers, the previous number will be retained. * When you assign 120 or 121 as the MIDI controller for the WHEEL, you should move the MODULATION Wheel to the mid-value then return it to the minimum value to send a relative MIDI message. * See Appendix B for a full list of controller numbers. 10. TRANSPOSE This function allows you to shift the pitch of the unit in semitones. You can transpose the pitch by 24 half steps (12 up, 12 down). · · Press the TRANSPOSE switch. The LED shows the current TRANSPOSE value. Press the "+" or "-" switch to change the TRANSPOSE value. Each time you press + or -, the keyboard is transposed an additional half step. * Pressing the + and - switches simultaneously resets the pitch to the default value. Note: Turning the power off always resets the shifted pitch to the default value. 11. · OCTAVE CHANGE This function allows you to shift the pitch up to three octaves higher or two lower. Press the OCTAVE UP or DOWN to change the octave range. The LED shows the new OCTAVE value. * Press OCTAVE UP and DOWN switches simultaneously to reset the pitch to the default value. Note: if the UP or DOWN switch is not pressed for 5 seconds, the LED will return to show the PROGRAM CHANGE number. 12. · · Sending BANK MSB and LSB message You can send any value of MSB or LSB from 0-127. The LED starts to flash showing the current value of the LSB. [. . . ] · Press the BANK LSB and BANK MSB keys together. · Hold the keys down for at about 2 seconds and the reset message is sent. 16. SPECIFICATIONS 1. Keyboard: 61 standard keys (Velocity sensitive) 2. Control: Switches: (WHEEL, CHANNEL, PROGRAM, MEMORY, TRANSPOSE, GM RESET, VEL CURVE, BANK LSB, BANK MSB, OCTAVE DOWN, OCTAVE UP, POWER ON/OFF, Numeric Keys (0-9), -, +) 3. [. . . ]