User manual FAGOR 2F2607

[. . . ] We recommend you have a fixed drainage exit at a distance of between 50 and 70 cm from the floor. Ensure that the drainage pipe is not too tight and that there are no folds or bottlenecks. a b max. 50 cm IMPORTANT It is important that the elbow of the pipe is properly fixed at the exit so that it doesn't fall, with the consequent risk of flooding. If your washing machine has an input for hot water, connect the tube with the red threading to the hot water tap and to the electrically operated valve with the red filter. [. . . ] The optional drawer should be placed in the wash compartment. Remember that the dose of detergent to be used always depends on G The amount of laundry to be washed. G The hardness of the water (You can request information on the water hardness from the competent local entities). ECOLOGICAL NOTE Remember that there are concentrated detergents that are more careful with nature and the environment. Using more detergent than is needed does not improve the wash results and as well as being a waste of money, it has a negative effect on the preservation of the environment. Therefore, please follow the instructions supplied by the manufacturer of the detergent. English 3 a b c d SELECTING THE WASH PROGRAMME There are four types of programme: Normal Programmes Delicate Programmes Wool Programmes Auxiliary Programmes To select the wash programme, please follow these steps: 1. Turn ON the machine (by pressing the programme selector, which pops out). Select the wash programme by turning the Programme Selector Dial. 1. 2. If your washing machine is a fully integrated model, instead of pressing the programme selector control, you have to press the button in the middle of the control panel, shown in the photo. display When you do this, the spin speed light corresponding to the selected programme will light up. If your washing machine has a display, when you select the programme, it will light up for a few seconds, showing P + programme number (P01. Then it will show the approximate duration of the programme in minutes. The time that appears on the display changes according to the progress of the programme ECOLOGICAL NOTE We recommend that you should choose the programme that is most suited to your wash, in order to avoid the pre-wash whenever possible. You will save money and help to preserve the environment. The display situated over the button will light up and the washing machine will start the selected programme with the options. If your washing machine has a display, you will be able to see how many minutes are left until the end of the wash. Switching on the delay This consists of pressing the on/off button after selecting the programme, the wash options and the delay time. On washing machines with a display, the screen will flash showing the time left before the programme starts. When the delay time has elapsed, it will stop flashing and show the duration of the IMPORTANT If you need to add or remove a garment, select pause and ensure that the water level is not over the door and that the inside temperature is not high. f you press the ON button, the wash will recommence at the same stage of the cycle where it stopped. programme selected. On washing machines with indicator lights, when the On/Off button is pressed, the time indicator will flash, successively showing the time remaining for the wash programme to begin. 6 STAGES IN WASH PROGRAMME ton during the wash has no effect on the washing IMPORTANT If you use the selector to change programmes while the machine is working, it will enter the PAUSE mode. The on/off light will go off and the programme will be annulled. If you press the On/ Off button during the wash, the washing machine will enter the PAUSE mode and this button's light will turn off. Pre-wash Wash Rinse End The active phases at each point of the programme shall appear as the programme progresses. Any option button may be selected as long as the phase in the programme in which it takes effect has not ended and as long as the programme allows this option. Pressing the delay but- 67 7 POWER CUTS stopped (it has an hour memory). The same occurs if your press the OFF button and then the ON button. In the event of a power cut, when the supply returns, the washing machine will continue to function normally, starting off where it had 8 TIPS G In order to reduce the noise produced during the spin cycle, level the washing machine using the adjustable feet. [. . . ] You didn't press the on/off button(this button's light should be on) The programme selector dial is not out. The door of the washing machine isn't closed properly. When this is detected, the displays that show "prewash" or "end" flash and F04 appears on the display of the washing machine. Then you should check if the door is open and close it properly. Why does the washing machine vibrate or make too much noise? Perhaps: The internal fastening screws were not removed. [. . . ]