User manual FAGOR 3FI-95G LST X

[. . . ] May we wish you all the very best with your modern appliance!All the operations concerned with the installation (electrical connection) must be carried out by qualified technicians, in terms with the standards in force. The ignition of the gas burner is carried out by putting a small flame to the upper part holes of the burner, pressing and rotating the corresponding knob in an anti-clockwise manner, until the maximum position has coincided with the marker. When the gas burner has been turned on, adjust the flame according to need. [. . . ] Evitare trabocchi di liquiTherefore, after boiling do; pertanto ad ebollizioor heating liquids, ne avvenuta o comunque reduce the heat output; a liquido riscaldato ridur- · Do not leave the electrical re l'erogazione di calore; plates on with empty · When cooking is finished, l'ébullition ou même, rotate the knob back into quand le liquide a été réclosing and/or disconchauffé, réduire l'émisnected position. Commutator 1 2 3 4 5 6 energy regulator 1-2 3-4 5-6 7-8 9 - 10 10 - 11 heat intensity slight mild slow medium high burning heat cooking methods melting of fats etc. ; heat small quantities of liquid heating of medium quantities of liquid; puddings, long-cooking sauces defreezing - heat large quantities of liquid; cooking below boiling temperature tender roasts; cooking at boiling temperature roasts - boiled food; pan-frying of meats bring large quantities of liquid to boil; fry Prior to any operation, disconnect the appliance from the electrical system. for long-life to the equipment , a general cleaning operation must take place periodically , bearing in mind the following: · The glass, steel and/or enamelled parts must be cleaned with suitable non-abrasive or corrosive products (found on the market). Avoid leaving acid or alkaline substances on the working area (vinegar, salt, lemon juice, etc. The wall baffle and the small covers (mobile parts of the burner) must be washed frequently with boiling water and detergent, taking care to remove every possible encrustation. Dry carefully and check that none of the burner holes is fully or partially clogged; · The electrical parts are cleaned with a damp cloth and are lightly greased with lubricating oil when still warm. The stainless steel grids of the working area, after having been heated, take on a bluish tint which does not deteriorate the quality. To bring colour back to its original state, use a slightly abrasive product. - Cleaning of the taps must be carried out by qualified personnel, who must be consulted In case of leakage, call immediately the qualified technicians for its replacement. -4a) First of all remove stray food bits and grease drops from the cooking surface with the special scraper (fig. Then clean the hot area as best as possible with SIDOL, STAHLFIX or other similar products with a papertowel, then rinse again with water and dry with a clean cloth. Pieces of aluminum foil and plastic material which have inadvertently melted or sugar remains or highly sacchariferous food have to be removed immediately from the hot cooking area with the special scraper (fig. Under no circumstances should abrasive sponges or irritating chemical detergents be used such as oven sprays or spot removers. This appliance is not provided with a combustion product discharge. it is recommended that it be installed in sufficiently aerated places , in terms of the laws in force. The quantity of air which is necessary for combustion must not be below 2. The appliance can be fitted into a working area as illustrated on the corresponding figure. Before positioning the hob, fit the seal around the entire periphery of the hole cut in the worktop. Furthermore, check that the feed pressure falls within the values described on the table: "User chacteristics". [. . . ] Appliance be pre-set for a different type of gas than that available, proceed as follows: · replace the injectors (Fig. 7) with the corresponding type of gas to be used (see table "Uses characteristics"). To adjust to the minimum, use a screwdriver on the screw placed on the tap (Fig. 8) after turning the tap to its minimum position. [. . . ]