User manual FAGOR 8040 M CNC

[. . . ] 1 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Keyboard customizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATING IN JOG MODE 2. 1 2. 2 2. 2. 1 2. 2. 2 2. 2. 3 2. 3 2. 4 2. 4. 1 2. 4. 2 2. 4. 3 2. 4. 4 2. 4. 4. 1 2. 4. 4. 2 2. 4. 4. 3 2. 5 2. 5. 1 2. 5. 2 2. 5. 3 2. 6 2. 6. 1 2. 6. 2 2. 6. 2. 1 2. 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Axis Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The CNC will assume this value. Enter the range number to be selected and press or Note: When the machine does not have spindle ranges this message is superfluous. For this reason, when text 28 of program 999997 is not defined, the CNC does not display this message. Chapter 2 - page 20 MCO-TCO work mode 2. 6. 2. 1 OPERATING AT CONSTANT SURFACE SPEED (CSS) When Constant Surface Speed operating mode is selected (CSS), the CNC assumes the spindle range selected at present. In this operating mode, when a new constant surface speed is selected, the following cases may arise: a) The spindle is stopped The CNC selects the new speed but does not apply this until the spindle moves. b) The spindle is started The CNC, depending on the position of the axis, calculates and makes the spindle turn at the corresponding rpm. speed for the Constant Surface Speed to be as defined. As the axes move, when working at Constant Surface Speed, the following cases may arise: a) The spindle is started The CNC moves the axes to the F programmed. As the X axis is moved, the CNC makes the spindle speed (rpm. ) match to maintain the constant surface speed selected. If the tool tip moves away from the turning axis the spindle revolutions therefore go down, and if it gets nearer, they go up. The CNC limits the spindle revolutions to the maximum speed set «SMAX». b) The spindle is stopped but a spindle speed S is selected The CNC calculates, in millimeters/minute, the feedrate corresponding to the last programmed "S" and moves the axis. For example, if «F 2. 000» and «CSS 500»: F (mm/min) = F (mm/min. ) x S (rev/min) = 2 x 500 = 1000 mm/min The axis moves at a feedrate of 1000 millimeters/minute c) The spindle is stationary and there is no spindle speed S selected. Warning The text for the screen title should be defined with the same number in the WGDRAW application as that of the screen. This way, when pressing the CNC will show the number and title (text of program P999995 of the same number) of the available screens. Chapter 3 - page 2 MCO-TCO work mode 3. 1 ASSOCIATED PROGRAMS In CO mode, programs P900000 through P999999 are reserved for the CNC itself and cannot be used as user part-programs. Some have a special meaning and must be defined by the machine manufacturer. P999001 through P999200 Configuration files defined by the manufacturer. P999001 for cycle 1, P999002 for cycle 2 and so on up to 999200 which is for cycle 200. P999500 Program which logs the errors occurred when interpreting a configuration file. P999994 Help texts of the OEM cycles (see Wgdraw manual). P999995 Texts and titles used by the OEM screens (see Wgdraw manual). P994xxx When the OEM cycles allow to define profiles, the operator defines them with 3 digits (0 through 999) and the CNC stores them internally as P994xxx. Profile 1 in P994001, Profile 2 in P994002 and so on. The rest of the programs reserved are for internal CNC use and MUST NOT be deleted. 3. 2 ASSOCIATED ROUTINES In CO mode, routines 0000 through 8999 are free and 9000 through 9999 are reserved to customize the CNC. [. . . ] or To l eave t gr phi s m ode pr s he a c es In the Operation Manual, M-MC or T-TC models, section «Graphics» in the «Execution / Simulation» chapter, there is an explanation of how to operate during graphics. Nevertheless, there will now be a brief description of the softkeys. It depends on the selected model MCO / TCO. Zone to be displayed Allows modification of the display zone, by defining the maximum and minimum coordinates of each axis. [. . . ]