User manual FAGOR FSO 900X

[. . . ] 2 Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Selection of tools and types of material to bend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A wrong value too different from the real one may cause uncontrolled movements of the axis. It displays the Y coordinate (Y = Yref - Hpunch - Hdie) compensating the height of the active tools. The led turns off. If on power-up, you wish to quit the home search mode without actually homing, press and key in the access (or quit) code: 719200. FSO 900X - Operating Manual - Page: 17 3. 2. 2 SEQUENCE FOR AXES WITHOUT MANDATORY HOME SEARCH In initial mode, press there are two choices: . Depending on the characteristics of the machine, a. If both axes have home switches, the "START" when accessing the top position. This unit displays the word only when the ram is at freely or accessing b. If any axis does not have a home switch, usually the Y, this unit requests the password 719200 to access the mode and assumes that the values set by the OEM are to be modified. This is only recommended in case of a breakdown or when updating this unit's software version. For the affected axis, proceed as described in section 3. 2. 1b 3. 2. 3 SEQUENCE FOR THE Y AXIS. MODEL B Proceed as indicated in 3. 2. 1a. and add the synchronization sequence: a. - with a linear encoder. Edit the data of the block using the procedures of the Editing mode described Editing P0007 N00 Select Tool - in section 4. 1. 2 and press . When modifying on the "Select axis" or "Attributes" screen, it may require pressing two or three times to accept the new value and assume it. The sequence ends with a blinking of the "#" symbol at the upper right hand of the screen and it is confirmed with two beeps. To learn how to insert a new block, see section 4. 2 To quit the Editing mode, press . - FSO 900X - Operating Manual - Page: 21 4. 1. 2 EDITING A NEW PROGRAM gives access to editing the header of the To edit a new program, pressing program (Block N00). The specific data for each bend take two screens pages. Use the key to go from one page or one block to the next while validating the data just entered. Use the keys to select the page to be displayed; but only on the block being edited (it is not possible to go back to the previous block). After validating a block, it is not possible to go back to it in order to change a value in it. To do this, finish editing the whole program and then proceed as described in section 4. 1. 1. Before accepting a data on the "Y" axis, in all the editing modes, it analyzes the requested bending depth and it cannot be written if they exceed the width of the die. The "angle" indicated when loading the tool data serves as a reference to force the safety limit Yminimum. [. . . ] X 123. 123 Y 123. 123 The number of decimals depends on the selected resolution. 6. 3 PROGRAM TRANSMITTING FORMAT The format is: P000 P0. M0 G0. 000 P999. 9 X Y R T H B D U Where: P0000 P0 - M0 G0. 000 P999. 9 XY R T H B D U Program number. Die number Sheet metal thickness Pressure (LF) Bend position Block execution number Delay between blocks (timing). Auxiliary output H (high) X axis retract Punch delay at the end of the bend (Delay) Top dead point (up) 6. 4 TRANSMISSION OF MATERIAL-TYPE TABLES In <Send> mode, this NC can send the full table stored in it out to a PC. In <Receive> mode, this NC can receive one or several materials M00 through M19 from a PC. FSO 900X - Operating Manual - Page: 33 APPENDIX ERROR CODES Message FAGOR dro Description Power outage or turned off by main switch after saving the data. [. . . ]