User manual FAGOR NC-200 PB OPERATION

[. . . ] FAGOR NC-200 PB NC FOR PRESS BRAKES OPERATING MANUAL Manual version 0111 INDEX Diagram of a typical press BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description of the various machine models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 1 2. 2 2. 3 2. 3. 1 2. 3. 2 2. 3. 3 2. 3. 4 2. 3. 5 3 3. 1 3. 1. 1 3. 1. 2 3. 1. 3 3. 1. 4 3. 2 3. 2. 1 3. 2. 2 3. 2. 3 3. 3 3. 3. 1 Unit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2- Press 3- Move the "Y" axis with to the far end position, towards Y-. Activate the BEND foot switch again up to the final position. Press Press again. to exit. Page: 18 - Operating Manual - NC-200 PB 3. 3 TOOL TABLE LOADING With this NC, it is possible to load the data of up to 10 sets of punches and dies. This data refers to the height of the punch (from 0. 000 mm and 9999. 999 mm), to the height of the die, width of the die, "V" (from 0. 000 mm to 9999. 999 mm), die angle that limits the bending depth and its edge radius (from 0 to 99. 9). To do this: - Access the editing mode by pressing The screen shows three options: Select "Punch" and press - Choose the tool number using - Indicate the punch height: - Press to exit. Edit Prg Punch Die or keying the number. [value] Select "Die" and press - Choose the tool number. - Indicate the die aperture with: - Indicate the die height with: - Indicate the die angle with: - Indicate the die edge radius with: - Press to exit [value] [value] [value] [value] · Before quitting this mode, it is recommended to check that none of the 9 table positions contains data exceeding the range with a code EEEEEEEE. By default, the whole table contains some initial values: Hpunch = 0, Hdie = 0, A = 16, r = 1. 6 that may be recalled. 3. 3. 1 RECALL INITIAL TOOL VALUES While in punch or die editing mode, press the sequence: F F The unit will request confirmation of this command. Select <Yes> and press to restore the initial values. NC-200 PB - Operating Manual - Page: 19 4 PROGRAMMING This NC can store up to 200 program blocks. The program memory may be locked setting installation parameter PAR51(1)=1 This way, the program blocks cannot be edited or deleted. In the initial teach-in stage, it is recommended to work with the simple resources only as a positioning dro without attributes and with a material factor M0 which only compensate for the rounding radius Rex = sheet metal thickness. Once familiarized with them, it is possible to expand the resources of the materialtype tables, program ANGLES with the same capabilities as specific CNC's for press brakes. To access this simple mode (without attributes): (The assumes the default values of D and T set by PAR29 and PAR30). · Press 5 1 · Press 8 to activate the bit and confirm with · Exit by pressing Programs edited in conversational mode keep the attributes even when not displayed in EDITOR mode if PAR51. 8 has been activated 4. 1 PROGRAM EDITING In a program, it is possible to "Edit" new blocks, "Modify" the data already programmed in the blocks or "Delete" all their contents leaving them free (empty). 4. 1. 1 EDITING / DELETING AN EXISTING PROGRAM Press mode. to access the block editing Edit Prg Punch Die - Select "Prg" using the press keys and Program Editing Program . . . . : 0000 - Use the keys to select the desired program to be modified (they are not stored sequentially). Press Program Editing Program . . . . : 0007 - Page: 20 - Operating Manual - NC-200 PB - Use the (Edit or Delete). Select "Delete" Select "Edit" keys to select the option Program Editing Edit Delete to delete a program from memory. . to modify. . · · · It access the program block N0. Only some values of the parameters affecting the geometry of the bend may be modified: Die number (with different width). When pressing , if the corrector has been stored, it recalculates all the following blocks that have been programmed by indicating the ANGLE in order to adapt them the new parameters of the N0 block and it will confirm that each one of them with two beeps. Edit the data of the block using the procedures of the Editing mode described Editing P0007 N00 Select Tool - in section 4. 1. 2 and press . When modifying on the "Select axis" or "Attributes" screen, it may require pressing two or three times to accept the new value and assume it. [. . . ] Power outage or turned off by main switch without having saved the data. The unit has been turned off without previously pushing the [ON/OFF] key. It will only lose the position count (will be reset to zero) and the status of the operating modes (inch, abs, etc. ). Wrong parameter values Wrong internal configuration Errors in data backup memory (Service Dept. ) Emergency input active. [. . . ]