User manual FALMEC DOWN DRAFT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FALMEC DOWN DRAFT. We hope that this FALMEC DOWN DRAFT user guide will be useful to you.

Lastmanuals help download the user guide FALMEC DOWN DRAFT.


FALMEC DOWN DRAFT : Download the complete user guide (23904 Ko)

Manual abstract: user guide FALMEC DOWN DRAFT

Detailed instructions for use are in the User's Guide.

[. . . ] EN - Temporary electrical connection (3); opening the hood for installation (4)(5). Remove the cover (6); remove the metal side panels (7); fix motor Remove the cover (9); remove the metal side panels (10); fix motor Front motor (13) back motor (14). EN - Replace the original "inlet" (15) with the bracket fixing the motor to the hood (16); secure the motor to the hood if the air exhaust is on the front (17). EN - Configuration with remote motor: Rectangular pipes (23); round pipes (24). [. . . ] Do not install the hood outdoors and do not expose it to outdoor environment (rain, wind, etc. Disconnect the equipment from electrical mains power supply before carrying out any operations on the hood. Ensure that the wires inside the hood are not disconnected or cut: in the event of damage, contact your nearest Servicing Department. Connection must be carried out in compliance with the provisions of law in force. Before connecting the hood to the electrical mains power supply, check that: · Voltage supply corresponds with what is reported on the data plate located inside the hood; · The electrical system is compliant and can withstand the load (see the technical specifications located inside the hood); · The power supply plug and cable do not come into contact with temperatures exceeding 70 °C; · The power supply system is effectively and properly connected to earth in compliance with regulations in force; · The socket used to connect the hood is within reach. in case of: · Devices fitted with cables without a plug: the type of plug to use is a ''stand- ardised'' one. The wires must be connected as follows: yellow-green for earthing, blue for neutral and brown for the phase. Fixed equipment not provided with a power supply cable and plug, or any other device that ensures disconnection from the electrical mains, with an opening gap of the contacts that enables total disconnection in overvoltage category III conditions. Said disconnection devices must be provided in the mains power supply in compliance with installation regulations. The Manufacturer declines all responsibility for failure to comply with the safety regulations. In this version the fumes and vapours are discharged outside through the exhaust pipe. To this end, the hood outlet fitting must be connected via a pipe, to an external output. The outlet pipe must have: · A diameter not less than that of the hood fitting. The minimum required length to avoid vibrations and reduce the suction per- formance of the hood. You are required to insulate the pipes if it passes through cold environments. In the presence of motors with 800m3/h or higher, a check valve is present to prevent external air flowing back. Deviation for Germany: when the kitchen hood is used at the same time as appliances that are powered by energy other than electricity, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). hOOD WITH INTERNAL RECIRCULATION (FILTERING) In this model, the air passes through the charcoal filters to be purified and recycled in the environment. Ensure that the active carbon filters are assembled into the hood, if not, install them as indicated in the assembly instructions. In this version the check valve must not be assembled: remove it if it is on the air outlet fitting of the motor. aSSEMBLY INSTRUCTIONS Only intended for qualified personnel The hood can be installed in various configurations. The generic assembly steps apply to all installations; for each case, follow the specific steps provided for the required installation. [. . . ] INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish to dispose of this appliance in other countries, we suggest contacting your local authorities or dealer to find out what the correct method of disposal is. The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation and reproduction, even partial, of this manual are bound by the Manufacturer's authorisation. Technical information, graphic representations and specifications in this manual are for information purposes and cannot be divulged. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FALMEC DOWN DRAFT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FALMEC DOWN DRAFT will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag