User manual FALMEC EUROPA INSTALLATION

[. . . ] (Tax rate = 4. 2500%) Key operation example Operator display Receipt print 550T! A Refund 200TU" A Receipt print Making a refund entry for a $ 3. 00 item (taxable 1). Key operation example Operator display Void  hen you void a following incorrect transaction: Selling W 300$ Ou A Making a refund entry for a $ 6. 00 item (non-taxable). Key operation example Operator display Key operation example a $1. 50 item (dept. 1) and a $2. 00 item (dept. 2) for cash, and receiving $5. 00 from your customer. [. . . ] When the low battery symbol is displayed, replace the batteries with new ones as soon as possible. The existent batteries will be dead in about two days. When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC adapter plug is disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any data stored in memory will be cleared. 4. Open the battery cover next to the paper roll cradle and remove the old batteries. 5. Insert the paper straight into the paper inlet, and press F. The paper then feeds through and appears in the print area. Drawer Handling Locking the Drawer Develop the habit of locking the drawer when not using the register for any extended period of time. To lock: Insert the key into the drawer lock and turn it 90 degrees counter-clockwise. To unlock: Insert the key into the drawer lock and turn it 90 degrees clockwise. 5. Install three new LR6 (“AA” size) batteries. Pass the paper end through the openings of the printer cover. Be very careful not to cut yourself on the manual cutter. C Improper use of batteries could cause them to burst or leak, which might damage the interior of the register. Please take the following precautions: • Be sure that the positive (+) and negative (-) poles of each battery are oriented properly. • Never mix batteries of different types. Tax Table Programming The tax table method requires tax break information from your state or local tax offices. Use the method which is acceptable in your state. You can obtain necessary data for tax programming from your local tax office. If you are in an area that uses a tax table for tax calculation, you can program the cash register accordingly. Tax table programming can be performed for Tax 1 and Tax 2. Sample tax table 1: Rate = 6% (*1) Amount of Sale Start End (Breakpoint) (*3) (*4) $0. 01 $0. 11 $0. 23 $0. 39 $0. 57 $0. 73 $0. 89 $1. 11 $1. 23 $1. 39 $1. 57 $1. 73 $1. 89 $0. 10 $0. 22 $0. 38 $0. 56 $0. 72 $0. 88 $1. 10 $1. 22 $1. 38 $1. 56 $1. 72 $1. 88 $2. 10 Tax $0. 00 $0. 01 $0. 02 $0. 03 $0. 04 $0. 05 $0. 06 $0. 07 $0. 08 $0. 09 $0. 10 $0. 11 $0. 12 End (minus) Start Difference 0. 10 0. 11 0. 15 0. 17 0. 15 0. 15 0. 21 0. 11 0. 15 0. 17 0. 15 0. 15 0. 21 Non-Cycle (*1) Tax rate: (2 digits integer and 4 digits decimal ) If rate has decimal value, decimal point is entered by v key . 4 digits) A tax table cycle is the repeating pattern of the tax rate found in your states tax table/chart. In tax table 1, where the 1st cycle begins ($0. 11) and the 2nd cycle begins ($1. 11) is a $1. 00 tax cycle. Tax cycle can vary from state-to-state, please check your local tax table for the exact cycle. Thus, the tax cycle can be determined by simply taking the differences between the first breakpoint of the cycle and the first breakpoint of the next cycle (example, $1. 11 -$0. 11 = $1. 00). 4 digits) Smallest amount for which tax must be collected. [. . . ] 4 digits) The tax amount increases in stages. The value of a taxable subtotal at which the tax amount changes is called a breakpoint. The difference between the start and end sales range. A group of breakpoint differences is repeated at regular intervals and each of these intervals is called a cycle. [. . . ]